BT-560T Network Card Settings and Configuration
BUSLOGIC, INC.
BT-560T
NIC Type | Ethernet |
Transfer Rate | 10Mbps |
Data Bus | 16-bit ISA |
Topology | Star |
Wiring Type | Shielded/Unshielded Twisted Pair AUI transceiver via DB-15 port |
Boot ROM | Available |
I/O CHANNEL READY | ||
Setting | JP1 | |
| » | Disabled | Pins 2 & 3 Closed |
Enable | Pins 1 & 2 Closed | |
Note:In some cases memory may require a lengthened transfer cycle. In these cases, the BT-560A must wait for a Host I/O READY signal (set to Host I/O Channel Ready Signal to Enabled). | ||
CARD FUNCTION | ||
Setting | SW1/1 | |
| » | Enabled | On |
Disabled | Off | |
INTERRUPT REQUEST | ||||
IRQ | SW1/2 | SW1/3 | SW1/4 | |
2/9 | Off | Off | On | |
10 | On | Off | On | |
11 | Off | On | On | |
| » | 15 | On | On | On |
DMA CHANNEL | |||
Channel | SW1/5 | SW1/6 | |
Disabled | Off | Off | |
DMA5 | On | Off | |
DMA6 | Off | On | |
| » | DMA7 | On | On |
DATA BUS TRANSFER RATE | |||
Setting | SW1/8 | SW1/9 | |
| » | 5MBps | On | On |
6.7MBps | On | Off | |
8MBps | Off | On | |
10MBps | Off | Off | |
Note:This setting specifies the rate at which the card transfers data (in Megabytes per second) on the data bus when acting as bus master. | |||
MEMORY STROBE-TIMING | ||
Setting | SW1/10 | |
| » | 150ns | On |
100ns | Off | |
Note:This switch selects the amount of time between the PC/AT's memory-write or memory-read command strobes. | ||
BOOT ROM ADDRESS | ||||||
Address | Boot ROM | SW2/1 | SW2/2 | SW2/3 | SW2/4 | |
C0000h | 8K or 16K | Off | Off | Off | Off | |
C2000h | 8K | On | Off | Off | Off | |
C4000h | 8K or 16K | Off | On | Off | Off | |
C6000h | 8K | On | On | Off | Off | |
C8000h | 8K or 16K | Off | Off | On | Off | |
CA000h | 8K | On | Off | On | Off | |
CC000h | 8K or 16K | Off | On | On | Off | |
CD000h | 8K | On | On | On | Off | |
D0000h | 8K or 16K | Off | Off | Off | On | |
D2000h | 8K | On | Off | Off | On | |
D4000h | 8K or 16K | Off | On | Off | On | |
D6000h | 8K | On | On | Off | On | |
D8000h | 8K or 16K | Off | Off | On | On | |
DA000h | 8K | On | Off | On | On | |
DC000h | 8K or 16K | Off | On | On | On | |
| » | DE000h | 8K | On | On | On | On |
BOOT ROM SIZE | |||
Size | SW2/5 | SW2/6 | |
| » | Disabled | On | On |
8K size | Off | On | |
16K size | On | Off | |
CABLE TYPE | ||
Type | SW2/7 | |
| » | Shielded/Unshielded Twisted Pair | On |
AUI transceiver via DB-15 port | Off | |
I/O BASE ADDRESS | ||||
Address | SW2/8 | SW2/9 | SW2/10 | |
100h | Off | Off | Off | |
120h | On | Off | Off | |
140h | Off | On | Off | |
160h | On | On | Off | |
300h | Off | Off | On | |
320h | On | Off | On | |
| » | 340h | On | On | On |
DIAGNOSTIC LED(S) | ||
LED | Status | Condition |
LED1 | Off | Twisted pair polarity is correctly configured |
LED1 | Off | Twisted pair polarity is incorrectly configured |
LED2 | On | Link is correctly configured /Link integrity test is disabled |
LED2 | Off | Link is incorrectly configured /Twisted pair connection is not in use |
LED3 | On | Data is being transmitted |
LED3 | Off | Data is not being transmitted |
LED4 | On | Data is being received |
LED4 | Off | Data is not being received |
My Books
