SCOUT PLUS (EXTERNAL) modem/telephone/ISDN Settings and Configuration

DIGICOM SYSTEMS

SCOUT PLUS (EXTERNAL)

Card Type
Modem, Fax
Chip Set
Unidentified
I/O Options
Line in (RJ-11), line out (RJ11), DTE port (25-pin serial connector),
power connector
Maximum Modem Rate
14.4Kbps
Maximum Fax Rate
9600bps
Data Modulation Protocol
Bell 212A, ITU-T V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol
V.27ter, V.29
Error Correction/Compression
MNP5, V.42, V42bis
Fax Class
Class I & II
Data Bus
External

CONNECTIONS
Function
Label
Function
Label
DTE port (25-pin serial connector)
CN1
Power jack
CN4
Line out
CN2
Power switch
SW2
Line in
CN3

USER CONFIGURABLE SETTINGS
Function
Label
Position
Normal operation enabled
SW1/1
Off
DCD forced high
SW1/1
On
í Factory configured - do not alter
SW1/2
Off

DIAGNOSTIC LED(S)
LED
Color
Status
Condition
MR
Unidentified
On
Power is on
MR
Unidentified
Off
Power is off
MR
Unidentified
Blinking
Modem has failed the self test
TR
Unidentified
On
DTR signal is high
TR
Unidentified
Off
DTR signal is low
AA
Unidentified
On
Auto-answer enabled
AA
Unidentified
Off
Auto-answer disabled
EC
Unidentified
On
Error correction enabled
EC
Unidentified
Off
Error correction disabled
HS
Unidentified
On
Modem is operating at high speed
HS
Unidentified
Off
Modem is not operating at high speed
RD
Unidentified
On
Modem is receiving data
RD
Unidentified
Off
Modem is not receiving data
SD
Unidentified
On
Modem is transmitting data
SD
Unidentified
Off
Modem is not transmitting data
CD
Unidentified
On
Carrier signal detected
CD
Unidentified
Off
Carrier signal not detected
CS
Unidentified
On
CTS signal is high
CS
Unidentified
Off
CTS signal is low
OH
Unidentified
On
Modem is off-hook
OH
Unidentified
Off
Modem is on-hook

SUPPORTED COMMAND SET
Basic AT Commands
AT, A/, +++
A, E, H, M, 0, V, Z
&F, &T, &Z

S Registers
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26

Note: See MHI Help file for full command documentation.

PROPRIETARY AT COMMAND SET

COMMUNICATIONS MODE
Type:
Configuration
Format:
AT [cmds] &Mn [cmds]
Description:
Selects communications mode
Command
Mode
&M0
Asynchronous mode

DATA CARRIER DETECT (DCD)
Type:
Configuration
Format:
AT [cmds] &Cn [cmds]
Description:
Selects whether the DCD option is enabled or disabled
Command
Function
&C0
DCD forced high
í &C1
DCD follows normal RS-232
&C2
DCD forced high (CD wink)

DATA SET READY (DSR)
Type:
Configuration
Format:
AT [cmds] &Bn [cmds]
Description:
Selects DSR options
Command
Function
í &B0
DSR forced high
&B1
DSR high only while modem is handshaking or connected
&B2
DSR follows normal RS-232

DATA TERMINAL READY (DTR)
Type:
Configuration
Format:
AT [cmds] &Dn [cmds]
Description:
Selects modem response to DTR
&D0
DTR forced high
&D1
Modem goes to command mode after DTR goes is off
í &D2
Modem goes to command mode and disconnects (hangs up) after DTR goes off
&D3
Modem is initialized after DTR goes off

DIAL
Type:
Immediate
Format:
AT [cmds] D<#> [cmds]
Description:
Dials telephone number according to any modifiers included in the string
Note:
Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command
Function
DP
Pulse dialing enabled
DSn
Dial stored telephone number n
DT
Tone dialing enabled/Pulse dialing disabled
DW
Dialing resumed following dial tone detection
D,
Dialing paused for amount of time specified in S8 register
D!
Modem commanded to go on-hook for ½ second
D@
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DISPLAY STORED TELEPHONE NUMBERS
Type:
Configuration
Format:
AT [cmds] &Sn [cmds]
Description:
Displays stored telephone numbers

ERROR CONTROL BREAK
Type:
Immediate
Format:
AT [cmds] Kn [cmds]
Description:
Controls break during error control
Command
Function
K0
Prevent break during error control
í K1
Allows break during error control

REPORT INFORMATION
Type:
Immediate
Format:
AT [cmds] In [cmds]
Description:
Displays information requested
Command
Function
I0
Reply with 960 or 961
I1
Send software version to DTE
I2
Send internal checksum to DTE

RESULT CODES
Type:
Configuration
Format:
AT [cmds] Qn [cmds]
Description:
Enables modem to send result codes to the DTE
Command
Function
í Q0
Result code sending enabled
Q1
Result code sending disabled
Q2
Result code sending enabled when in originate mode

RTS/CTS
Type:
Configuration
Format:
AT [cmds] &Rn [cmds]
Description:
Selects RTS/CTS options
Command
Function
&R0
CTS follows RTS in data mode
&R1
CTS follows DCD signal
&R2
CTS forced high

SELECT CALL PROGRESS RESULT CODES
Type:
Configuration
Format:
AT [cmds] Xn [cmds]
Description:
Enables selection of tone detection and associated result code format options
Command
Function
X0
Busy and dial tone detection disabled; basic result codes enabled
X1
Busy and dial tone detection disabled; extended result codes enabled.
X2
Busy tone detection disabled, dial tone detection enabled; extended result codes enabled.
X3
Busy tone detection enabled, dial tone detection disabled; extended result codes enabled.
X4
Busy and dial tone detection enabled; extended result codes enabled.
X5
Busy and dial tone detection enabled; basic result codes enabled.

STORE ACTIVE PROFILE
Type:
Configuration
Format:
AT [cmds] &Wn [cmds]
Description:
Writes the values for the active profile into the non-volatile RAM

EXTENDED AT COMMAND SET

ABORT FEATURE
Type:
Configuration
Format:
AT [cmds] *Pn [cmds]
Description:
Enable/disable user abort feature
Command
Function
í *P0
User abort feature enabled
*P1
User abort feature disabled

ADAPTIVE HANDSHAKE
Type:
Configuration
Format:
AT [cmds] *Gn [cmds]
Description:
Enables/disables adaptive handshake
Command
Function
*G0
Adaptive handshake disabled
í *G1
Adaptive handshake enabled

CONNECTION SPEED
Type:
Configuration
Format:
AT [cmds] *Nn [cmds]
Description:
Controls modem connection rate
Command
Function
*N0
Connect at 1200bps
*N1
Connect at 2400bps
*N2
Connect at 4800bps
í *N3
Connect at 9600bps
*N4
Connect at 7200bps
*N5
Connect at 12.0Kbps
*N6
Connect at 14.4Kbps

ERROR CONTROL
Type:
Configuration
Format:
AT [cmds] *En [cmds]
Description:
Selects error control
Command
Function
*E0
EC error control disabled
*E1
Auto-reliable MNP5 error control enebled
*E2
MNP5 error control enabled
*E3
Auto-reliable error control up to class 4 enabled
*E4
Reliable error control up to class 4 enabled
*E5
Auto-reliable V.42 with phase detection enabled
*E6
Reliable V.42 with phase detection enabled
*E7
Auto reliable V.42 without phase detection enabled
*E8
Reliable V.42 without phase detection enabled
í *E9
Auto-reliable V.42bis with phase detection enabled
*E10
reliable V.42bis with phase detection enabled

ERROR CORRECTION RESPONSES
Type:
Configuration
Format:
AT [cmds] *Mn [cmds]
Description:
Controls error correction response sending
Command
Function
*M0
Error correction response sending disabled
í *M1
Error correction response sending enabled
*M2
Error correction response sending with type of error correction enabled

FLOW CONTROL
Type:
Configuration
Format:
AT [cmds] *Fn [cmds]
Description:
Sets type of flow control used by modem
Command
Function
*F0
Flow control disabled
*F1
XON/XOFF passthrough flow control enabled
*F2
XON/XOFF flow control enabled
í *F3
RTS/CTS flow control enabled

PARAMETER SETTINGS
Type:
Configuration
Format:
AT [cmds] *On [cmds]
Description:
Displays current parameter settings

SIGNAL QUALITY
Type:
Configuration
Format:
AT [cmds] *Qn [cmds]
Description:
Controls retrain, adaptive rate, and disconnect
Command
Function
*Q0
Quality signal action enabled
í *Q1
Retrain enabled
*Q2
Adaptive rate enabled
*Q3
Disconnect

SPEED CONVERSION
Type:
Configuration
Format:
AT [cmds] *Sn [cmds]
Description:
Enable/disable speed conversion
Command
Function
*S0
Speed conversion disabled
í *S1
Speed conversion enabled

TRELLIS CODING
Type:
Configuration
Format:
AT [cmds] *Tn [cmds]
Description:
Enable/disable trellis coding
Command
Function
*T0
Trellis coding disabled
í *T1
Trellis coding enabled

S(STATUS) -REGISTERS

DATA COMPRESSION/ ERROR CORRECTION ABORT
Type:
Register
Format:
AT [cmds] S15=n [cmds]
Range:
33-255
Unit:
ASCII
Description:
Aborts a data compression/error correction during negotiation
Note
The parameter may be changed with characters 33-127. Any value after 128 is (OFF)

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

SCOUT PLUS (EXTERNAL) modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem, Fax
Chip Set	Unidentified
I/O Options	Line in (RJ-11), line out (RJ11), DTE port (25-pin serial connector), power connector
Maximum Modem Rate	14.4Kbps
Maximum Fax Rate	9600bps
Data Modulation Protocol	Bell 212A, ITU-T V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol	V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V42bis
Fax Class	Class I & II
Data Bus	External

CONNECTIONS
Function	Label		Function		Label
DTE port (25-pin serial connector)		CN1		Power jack		CN4
Line out		CN2		Power switch		SW2
Line in		CN3

USER CONFIGURABLE SETTINGS
Function	Label	Position
Normal operation enabled	SW1/1	Off
DCD forced high	SW1/1	On
í Factory configured - do not alter	SW1/2	Off

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
MR	Unidentified	On	Power is on
MR	Unidentified	Off	Power is off
MR	Unidentified	Blinking	Modem has failed the self test
TR	Unidentified	On	DTR signal is high
TR	Unidentified	Off	DTR signal is low
AA	Unidentified	On	Auto-answer enabled
AA	Unidentified	Off	Auto-answer disabled
EC	Unidentified	On	Error correction enabled
EC	Unidentified	Off	Error correction disabled
HS	Unidentified	On	Modem is operating at high speed
HS	Unidentified	Off	Modem is not operating at high speed
RD	Unidentified	On	Modem is receiving data
RD	Unidentified	Off	Modem is not receiving data
SD	Unidentified	On	Modem is transmitting data
SD	Unidentified	Off	Modem is not transmitting data
CD	Unidentified	On	Carrier signal detected
CD	Unidentified	Off	Carrier signal not detected
CS	Unidentified	On	CTS signal is high
CS	Unidentified	Off	CTS signal is low
OH	Unidentified	On	Modem is off-hook
OH	Unidentified	Off	Modem is on-hook

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Selects communications mode
Command	Mode
&M0	Asynchronous mode

DATA CARRIER DETECT (DCD)
Type:	Configuration
Format:	AT [cmds] &Cn [cmds]
Description:	Selects whether the DCD option is enabled or disabled
Command	Function
&C0	DCD forced high
í &C1	DCD follows normal RS-232
&C2	DCD forced high (CD wink)

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Bn [cmds]
Description:	Selects DSR options
Command	Function
í &B0	DSR forced high
&B1	DSR high only while modem is handshaking or connected
&B2	DSR follows normal RS-232

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
&D0	DTR forced high
&D1	Modem goes to command mode after DTR goes is off
í &D2	Modem goes to command mode and disconnects (hangs up) after DTR goes off
&D3	Modem is initialized after DTR goes off

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DP	Pulse dialing enabled
DSn	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Modem commanded to go on-hook for ½ second
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DISPLAY STORED TELEPHONE NUMBERS
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Displays stored telephone numbers

ERROR CONTROL BREAK
Type:	Immediate
Format:	AT [cmds] Kn [cmds]
Description:	Controls break during error control
Command	Function
K0	Prevent break during error control
í K1	Allows break during error control

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reply with 960 or 961
I1	Send software version to DTE
I2	Send internal checksum to DTE

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE
Command	Function
í Q0	Result code sending enabled
Q1	Result code sending disabled
Q2	Result code sending enabled when in originate mode

RTS/CTS
Type:	Configuration
Format:	AT [cmds] &Rn [cmds]
Description:	Selects RTS/CTS options
Command	Function
&R0	CTS follows RTS in data mode
&R1	CTS follows DCD signal
&R2	CTS forced high

SELECT CALL PROGRESS RESULT CODES
Type:	Configuration
Format:	AT [cmds] Xn [cmds]
Description:	Enables selection of tone detection and associated result code format options
Command	Function
X0	Busy and dial tone detection disabled; basic result codes enabled
X1	Busy and dial tone detection disabled; extended result codes enabled.
X2	Busy tone detection disabled, dial tone detection enabled; extended result codes enabled.
X3	Busy tone detection enabled, dial tone detection disabled; extended result codes enabled.
X4	Busy and dial tone detection enabled; extended result codes enabled.
X5	Busy and dial tone detection enabled; basic result codes enabled.

STORE ACTIVE PROFILE
Type:	Configuration
Format:	AT [cmds] &Wn [cmds]
Description:	Writes the values for the active profile into the non-volatile RAM

ABORT FEATURE
Type:	Configuration
Format:	AT [cmds] *Pn [cmds]
Description:	Enable/disable user abort feature
Command	Function
í *P0	User abort feature enabled
*P1	User abort feature disabled

ADAPTIVE HANDSHAKE
Type:	Configuration
Format:	AT [cmds] *Gn [cmds]
Description:	Enables/disables adaptive handshake
Command	Function
*G0	Adaptive handshake disabled
í *G1	Adaptive handshake enabled

CONNECTION SPEED
Type:	Configuration
Format:	AT [cmds] *Nn [cmds]
Description:	Controls modem connection rate
Command	Function
*N0	Connect at 1200bps
*N1	Connect at 2400bps
*N2	Connect at 4800bps
í *N3	Connect at 9600bps
*N4	Connect at 7200bps
*N5	Connect at 12.0Kbps
*N6	Connect at 14.4Kbps

ERROR CONTROL
Type:	Configuration
Format:	AT [cmds] *En [cmds]
Description:	Selects error control
Command	Function
*E0	EC error control disabled
*E1	Auto-reliable MNP5 error control enebled
*E2	MNP5 error control enabled
*E3	Auto-reliable error control up to class 4 enabled
*E4	Reliable error control up to class 4 enabled
*E5	Auto-reliable V.42 with phase detection enabled
*E6	Reliable V.42 with phase detection enabled
*E7	Auto reliable V.42 without phase detection enabled
*E8	Reliable V.42 without phase detection enabled
í *E9	Auto-reliable V.42bis with phase detection enabled
*E10	reliable V.42bis with phase detection enabled

ERROR CORRECTION RESPONSES
Type:	Configuration
Format:	AT [cmds] *Mn [cmds]
Description:	Controls error correction response sending
Command	Function
*M0	Error correction response sending disabled
í *M1	Error correction response sending enabled
*M2	Error correction response sending with type of error correction enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] *Fn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
*F0	Flow control disabled
*F1	XON/XOFF passthrough flow control enabled
*F2	XON/XOFF flow control enabled
í *F3	RTS/CTS flow control enabled

PARAMETER SETTINGS
Type:	Configuration
Format:	AT [cmds] *On [cmds]
Description:	Displays current parameter settings

SIGNAL QUALITY
Type:	Configuration
Format:	AT [cmds] *Qn [cmds]
Description:	Controls retrain, adaptive rate, and disconnect
Command	Function
*Q0	Quality signal action enabled
í *Q1	Retrain enabled
*Q2	Adaptive rate enabled
*Q3	Disconnect

SPEED CONVERSION
Type:	Configuration
Format:	AT [cmds] *Sn [cmds]
Description:	Enable/disable speed conversion
Command	Function
*S0	Speed conversion disabled
í *S1	Speed conversion enabled

TRELLIS CODING
Type:	Configuration
Format:	AT [cmds] *Tn [cmds]
Description:	Enable/disable trellis coding
Command	Function
*T0	Trellis coding disabled
í *T1	Trellis coding enabled

DATA COMPRESSION/ ERROR CORRECTION ABORT
Type:	Register
Format:	AT [cmds] S15=n [cmds]
Range:	33-255
Unit:	ASCII
Description:	Aborts a data compression/error correction during negotiation
Note	The parameter may be changed with characters 33-127. Any value after 128 is (OFF)