14.4 ATF/ATV/ACF/ACV FAX MODEM modem/telephone/ISDN Settings and Configuration

Card Type	Modem (asynchronous), Fax
I/O Options	RJ-11 line in, RJ-11 line out
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation	Unidentified
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I & II
Data Bus	8-bit ISA

CONNECTIONS
Function	Label	Function	Label
RJ-11 line	CN1	RJ-11 line	CN2

SERIAL PORT ADDRESS SELECTION
Setting	J9	J10
3F8h (COM1:)	Pins 1 & 2 closed	Pins 1 & 2 closed
2F8h (COM2:)	Pins 1 & 2 closed	Pins 2 & 3 closed
3E8h (COM3:)	Pins 2 & 3 closed	Pins 1 & 2 closed
2E8h (COM4:)	Pins 2 & 3 closed	Pins 2 & 3 closed

INTERRUPT SELECTION
Setting	J5	J6	J7	J8
3	Open	Open	Open	Closed
4	Open	Open	Closed	Open
5	Open	Closed	Open	Open
7	Closed	Open	Open	Open

SUPPORTED STANDARD COMMANDS

Basic AT Commands

AT, A/

A, B, C, E, F, H, M, O, V, W, X, Y, Z

&C, &F, &J, &L, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \L, \O, \T, \U, \Z

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, S16, S18, S21, S22, S23 S25, S26

S27, S30, S36, S37, S38, S40, S41, S46, S48, S82, S86, S91, S95

Note: See MHI help file for complete information.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects options for handshake modulation
Command	Function
N0	Speed of connection follows speed set in register S7
N1	Negotiate at highest possible speed

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Qn [cmds]
Description:	Selects communications mode options
Command	Mode
&Q0	Asynchronous mode, serial port speed follows connect speed.
&Q1	Asynchronous off-line command mode and synchronous connect mode.
&Q2	Asynchronous off-line command mode - modem autodials first number in directory, then synchronous connect mode.
&Q3	Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR.
&Q5	Error correction mode
&Q6	Buffered asynchronous mode
&Q8	MNP mode
&Q9	V.42bis mode

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR loss

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D^	1300Hz calling tone enabled
D;	return to command state after dialing

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
&K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
&P0	39/61ms at 10pps (North America)
&P1	33/67ms at 10pps (Europe)
&P2	39/61ms at 20pps

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports firmware checksum
I2	Tests and reports firmware checksum
I3	Reports firmware revision level
I4	Reports product capabilities

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE
Command	Function
Q0	Result code sending enabled
Q1	Result code sending disabled
Q2	Result code sending enabled in originate mode

SOFT RESET
Type:	Immediate
Format:	AT [cmds] Zn [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall-forward
Command	Function
%E0	Auto-retrain disabled
%E1	Auto-retrain enabled

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Function
\K0	Online command mode enabled, send no break to remote modem
\K1	Break sent to remote modem and buffered cleared
\K3	Send break to remote modem immediately
\K5	Send break with transmitted data

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	Data compression enabled

COMPRESSION MODE
Type:	Configuration
Format:	AT [cmds] %Mn [cmds]
Description:	Selects data compression mode
Command	Function
%M0	Compression disabled
%M1	Transmit only
%M2	Receive only
%M3	Transmit/receive compression enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled

DICTIONARY SIZE
Type:	Configuration
Format:	AT [cmds] %Dn [cmds]
Description:	Selects data compression
Command	Function
%D0	512 bytes
%D1	1024 bytes
%D2	2048 bytes
%D3	4096 bytes

ECHO DATA
Type:	Configuration
Format:	AT [cmds] \En [cmds]
Description:	Enables modem to echo received data
Command	Function
\E1	One shot optimization

SPEED BUFFER LOWER LIMT
Type:	Register
Format	AT [cmds] S49=n [cmds]
Range:	1-255
Unit:	Unidentified
Description:	Sets speed buffer lower limit. Default=8.

SPEED BUFFER UPPER LIMT
Type:	Register
Format	AT [cmds] S50=n [cmds]
Range:	1-255
Unit:	Unidentified
Description:	Sets speed buffer lower limit. Default=255.