MAGIC MP32 modem/telephone/ISDN Settings and Configuration

Card Type	Modem, Fax, Sound card
Chip Set	Unidentified
I/O Options	CD-ROM interface, microphone, audio line in, audio line out, wavetable interface
Maximum Modem Rate	33.6Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29, V.33
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I & II
Data Bus	16-bit ISA
Card Size	Full-length, full-height card

CONNECTIONS
Function	Label		Function		Label
MIDI/Game port		CN1		Wave table interface		CN6
Telephone line in		CN4		Speaker/Line out		CN7
Telephone line out		CN5		Line in		CN8
Microphone in		CN9		CD-Audio		JP5

SPEAKER/LINE OUT SETTINGS
Function	CN2	CN3
Speaker mode enabled (CN7)	Pins 1 & 2 closed	Pins 1 & 2 closed
Line out function enabled	Pins 2 & 3 closed	Pins 2 & 3 closed

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, C, D, E, H, M, O, P, Q, T, V, W, X, Y, Z

&C, &F, &P, &Q, &R, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \K, \N, \V,

%C, %E, %L, %Q, %TT

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91,

S92, S95

Special Commands

#CID, +MS, #BDR, #CLS, MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN,

#VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX

Note: See MHI Help File for full command documentation.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
N1	Auto-mode detection enabled

CLOCK SOURCE - SYNCHRONOUS TRANSMIT
Type:	Configuration
Format:	AT [cmds] &Xn [cmds]
Description:	Selects DTE transmit clock source
Command	Function
&X0	Modem generates clock
&X1	Modem generates clock from the receive carrier signal

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Selects communications mode
Command	Mode
&M0	Asynchronous mode
&M1	Synchronous connect mode and asynchronous off-line command mode.
&M2	Synchronous connect mode and asynchronous off-line command mode and set DTR high.
&M3	Synchronous connect mode and asynchronous off-line command mode and set DTR to low.

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Note: The action each variant of &D causes depends on the setting of &Q
&Q Setting		&D0	&D1	&D2	&D3
&Q0, &Q5, &Q6		Command 0	Command 1	Command 2	Command 3
&Q1, &Q4		Command 2	Command 1	Command 2	Command 3
&Q2, &Q3		Command 2	Command 2	Command 2	Command 2
Command	Function
Command 0	Modem does not respond to DTR
Command 1	Modem goes to command mode after DTR goes is off
Command 2	Modem goes to command mode and disconnects (hangs up) after DTR goes off.
Command 3	Modem is initialized after DTR goes off

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
&K3	RTS/CTS and DTE/DCE flow control enabled
&K4	XON/XOFF and DTE/DCE flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	RTS/CTS and XON/XOFF flow control enabled

GUARD TONE
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Commands the modem to transmit a guard tone in V.22/V.22bis
Note: Used primarily for international data transmission
Command	Function
&G0	Guard tone disabled
&G1	Guard tone disabled
&G2	1800Hz guard tone enabled

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports modem model and speed
I1	Reports ROM checksum
I2	Reports OK
I3	Reports firmware revision, model and interface type
I4	Reports response programmed by OEM
I5	Reports the country code parameter
I6	Reports modem data pump model and code revision

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

TEST MODES
Type:	Immediate
Format:	AT [cmds] &Tn
Description:	Selects test options
Command	Function
&T0	End current test
&T1	Begin local analog loopback test
&T2	Returns error result code
&T3	Begin local digital loopback
&T4	Grant remote digital loopback request
&T5	Deny remote digital loopback request
&T6	Request remote digital loopback
&T7	Request remote digital loopback and self-test
&T8	Begin local analog loopback and self-test

AUTOSYNC OPTIONS
Type:	Register
Format	AT [cmds] S19=n
Default:	0
Description:	Enables selection of the autosync options

AUTOSYNC OR BSC SYNC ENABLED
Type:	Register
Format	AT [cmds] S20=n
Default:	0
Description:	Enables autosync HDLC address or BSC sync characters