5532DMA REV.0 IO card Settings and Configuration

Card Type	Data Aquisition
Chip Set	Unidentified
Maximum Onboard Memory	Unidentified
I/O Options	Analog input, digital input
Hard Drives supported	None
Floppy drives supported	None
Data Bus	8-bit ISA
Card Size	Half length

CONNECTIONS
Function	Label
50-pin analog/digital signals connector	J1

PORT A/B DMA CHANNEL SELECTION
Channel	W22	W23	W24	W28	W29	W30
1	Open	Open	Closed	Closed	Open	Open
2	Open	Closed	Open	Open	Closed	Open
3	Closed	Open	Open	Open	Open	Closed
Disabled	Open	Open	Open	Open	Open	Closed

PORT C/D DMA CHANNEL SELECTION
Channel	W25	W26	W27	W31	W32	W33
1	Open	Open	Closed	Closed	Open	Open
2	Open	Closed	Open	Open	Closed	Open
3	Closed	Open	Open	Open	Open	Closed
Disabled	Open	Open	Open	Open	Open	Closed

DIO PORT A CONFIGURATION
Function		Label	Position
	8 bit input mode enabled	JP2	Pins 2 & 3 closed
	16 bit input mode enabled	JP2	Pins 1 & 2 closed
»	Input enabled	W10	Closed
	Output enabled	W10	Open
Note: In 16 bit mode, port A data is latched when port B data is latched.

DIO PORT B CONFIGURATION
Function		Label	Position
»	Input enabled	W11	Closed
	Output enabled	W11	Open
»	IRQ interrupt disabled	W14	Open
	IRQ interrupt enabled	W14	Closed
»	Handshaking output disabled	W35	Closed
	Handshaking output enabled	W35	Open
»	Handshaking input disabled	W36	Closed
	Handshaking input enabled	W36	Open

DIO PORT C CONFIGURATION
Function		Label	Position
	8 bit input mode enabled	JP1	Pins 2 & 3 closed
	16 bit input mode enabled	JP1	Pins 1 & 2 closed
»	Output enabled	W12	Open
	Input enabled	W12	Closed
Note: In 16 bit mode, port C data is latched when port D data is latched.

DIO PORT D CONFIGURATION
Function		Label	Position
»	Output enabled	W13	Open
	Input enabled	W13	Closed
»	IRQ interrupt disabled	W15	Open
	IRQ interrupt enabled	W15	Closed
»	Handshaking output disabled	W34	Closed
	Handshaking output enabled	W34	Open
»	Handshaking input disabled	W37	Closed
	Handshaking input enabled	W37	Open

BASE I/O ADDRESS SELECTION
Setting		W9	W8	W7	W6	W5	W4	W3
	000h	Open	Open	Open	Open	Open	Open	Open
	008h	Open	Open	Open	Open	Open	Open	Closed
	010h	Open	Open	Open	Open	Open	Closed	Open
	018h	Open	Open	Open	Open	Open	Closed	Closed
	020h	Open	Open	Open	Open	Closed	Open	Open
»	100h	Open	Closed	Open	Open	Open	Open	Open
	3D8h	Closed	Closed	Closed	Closed	Open	Closed	Closed
	3E0h	Closed	Closed	Closed	Closed	Closed	Open	Open
	3E8h	Closed	Closed	Closed	Closed	Closed	Open	Closed
	3F0h	Closed	Closed	Closed	Closed	Closed	Closed	Open
	3F8h	Closed	Closed	Closed	Closed	Closed	Closed	Closed
Note: A total of 128 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. W9 is the Most Significant Bit and jumper W3 is the Least Significant Bit. The jumpers have the following decimal values:W9=512, W8=256, W7=128, W6=64, W5=32, W4=16, W3=8. Turn off the switches and add the values of the switches to obtain the correct memory address. (Close=1, Open=0)

IRQ INTERRUPT SELECTION
IRQ		W16	W17	W18	W19	W20	W21
	IRQ2	Closed	Open	Open	Open	Open	Open
	IRQ3	Open	Closed	Open	Open	Open	Open
	IRQ4	Open	Open	Closed	Open	Open	Open
	IRQ5	Open	Open	Open	Closed	Open	Open
	IRQ6	Open	Open	Open	Open	Closed	Open
»	IRQ7	Open	Open	Open	Open	Open	Closed