5508SHR REV.1 IO card Settings and Configuration

Card Type

Data Aquisition

Chip Set

Unidentified

Maximum Onboard Memory

Unidentified

I/O Options

Analog input, digital input

Hard Drives supported

None

Floppy drives supported

None

Data Bus

16-bit ISA

Card Size

Three-quarter length

CONNECTIONS

Function

Label

Function

Label

37-pin analog/digital signals connector

J1

A/D converter range selector

R101

A/D offset selector

R100

Common mode selector

R102

DMA CHANNEL SELECTION

Channel

W10

W11

W12

W13

W14

W15

»

Disabled

Open

Open

Open

Open

Open

Open

1

Open

Open

Closed

Open

Open

Closed

2

Open

Closed

Open

Open

Closed

Open

3

Closed

Open

Open

Closed

Open

Open

A/D TRIGGER SOURCE SELECTION

Mode

JP1

W1

»

H/W trigger source = Counter 0

Pins 2 & 3 closed

Open

External trigger

Pins 1 & 2 closed

Open

Scan mode triggering

Pins 2 & 3 closed

Closed

Note: Scan mode triggering initiates triggers from counter 0 on receipt of external trigger.

COUNTER SOURCE SETTINGS

Counter

Setting

Label

Position

»

Counter 1 clock source

External (clock 1)

JP5

Pins 2 & 3 closed

Counter 1 clock source

4.00 MHz oscillator

JP5

Pins 1 & 2 closed

»

Counter 2 clock source

External (clock 2)

JP6

Pins 2 & 3 closed

Counter 2 clock source

4.00 MHz oscillator

JP6

Pins 1 & 2 closed

DIGITAL I/O PORT CONFIGURATION

Function

Label

Position

»

Port 1 (DIO4-DIO7) output

W2

Open

Port 1 (DIO4-DIO7) input

W2

Closed

»

Port 0 (DIO0-DIO3) input

W3

Closed

Port 0 (DIO0-DIO3) output

W3

Open

BASE I/O ADDRESS SELECTION

Setting

W9

W8

W7

W6

W5

W4

000h

Open

Open

Open

Open

Open

Open

010h

Open

Open

Open

Open

Open

Closed

020h

Open

Open

Open

Open

Closed

Open

030h

Open

Open

Open

Open

Closed

Closed

040h

Open

Open

Open

Closed

Open

Open

»

110h

Open

Closed

Open

Open

Open

Closed

3B0h

Closed

Closed

Closed

Open

Closed

Closed

3C0h

Closed

Closed

Closed

Closed

Open

Open

3D0h

Closed

Closed

Closed

Closed

Open

Closed

3E0h

Closed

Closed

Closed

Closed

Closed

Open

3F0h

Closed

Closed

Closed

Closed

Closed

Closed

A total of 64 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. W9 is the Most Significant Bit and switch W4 is the Least Significant Bit. The switches have the following decimal values: W9=512, W8=256, W7=128, W6=64, W5=32, W4=16. Turn off the switches and add the values of the switches to obtain the correct memory address. (Close=1, Open=0)

IRQ INTERRUPT SELECTION

IRQ

JP2

JP3

JP4

IRQ2

Open

Open

Pins 1 & 2 closed

IRQ3

Open

Pins 1 & 2 closed

Open

IRQ4

Pins 1 & 2 closed

Open

Open

IRQ5

Open

Open

Pins 2 & 3 closed

IRQ6

Open

Pins 2 & 3 closed

Open

IRQ7

Pins 2 & 3 closed

Open

Open

»

Disabled

Open

Open

Open