Hard Drive: IBM: DTNA-22160 TRAVE.4LP 2160MB 2.5"/SSL ATA2 FAST

D T N A - 2 2 1 6 0   T R A V E . 4 L P    IBM
                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders        | 4200|     |
Capacity form/unform  2160/      MB        Heads            |   16|     |
Seek time   / track  13.0/ 4.0 ms          Sector/track     |   63|     |
Controller           IDE / ATA2 FAST/ENHA  Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate    7.000 MB/S int       Bytes/Sector      512
                     16.600 MB/S ext PIO4
Recording method                                    operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 65
Power: sleep          0.1 W     Humidity     %         8 90    |      5 95
       standby        0.3 W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle           0.9 W     Shock        g       100       |    500
       seek           2.3 W     Rotation   RPM      4000
       read/write     2.3 W     Acoustic   dBA
       spin-up        4.7 W     ECC        Bit   SMART
                                MTBF         h
                                Warranty Month
Lift/Lock/Park     YES          Certificates

Layout

IBM DTNA-21800/22160 JUMPER SETTING

              +--------------------------------------+
              |                                      |
              |                                      |
              |                                      |
              +--------Interface-------------49------+
              |       **********************1 **47 Jumper
              |       *************x********* **48   |
              +------44----------------------50------+
              +                                      +

Pin position 20 is left blank for secure connector insertion.

 Pin position 49: When grounded, no spin-up at POR when open/pull up,
                  normal spin-up at POR.

Jumpers

IBM DTNA-21800/22160 QUICK INSTALLATION GUIDE

Jumper Setting
==============

Drive Address Setting
---------------------
A jumper is available at the interface connector to determine the
drive address.

Using Cable Selection, the drive address depends on the condition of
pin 28 of the AT interface cable. In the case when pin 28 is ground
or low, the drive is a Master. If pin 28 is open or high level, the
drive is a Slave.

   ---49--47+
    *   * * | Master
    *   * * | (Default setting)
   ---50--48+

   ---49--47+
    *   * X | Slave
    *   * X |
   ---50--48+

   ---49--47+
    *   * * | Cable Selection
    *   xxx |
   ---50--48+

   ---49--47+
    *   xxx | RESERVED       (MASTER)
    *   * * |
   ---50--48+

   ---49--47+
    *   X * | NEVER ATTACH A JUMPER HERE!
    *   X * |
   ---50--48+

 49-PIN: When grounded, no spin-up at POR
         When open/pull-up, normal spin-up at POR

Install

IBM DTNA-21800/22160 JUMPER SETTING

Notes On Installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

The drive will operate in all axis (6 directions).

Cabling
-------
The maximum cable length from the host system to tge HDD plus circuit
pattern in the host system shall not exceed 18 inches.

AT Signal Connector
-------------------
The AT Signal Connector is designed to mate with Dupont part number
69764-044 or equivalent.

NOTES
Pin position 20 is left blank for secure connector insertion.

Pin 49: When grounded, No Spin-up at POR when open/pull up, Normal
Spin-up at POR.

 NOTE Interface Signals
 ----------------------
 There are two input pins for +5 Volt power supply, "+5V Logic"
 (Pin 41) and "+5V Motor" (Pin 42). Pin 41 is connected to the
 internal logic circuits and Pin 42 is connected to the spindle motor
 and motor drive.

 It is possible to turn on and off +5V Logic by an external switch
 circuit to reduce power consumption to the least possible. In this
 mode, a voltage drop out due to the motor spin up current can be
 reduced by connecting +5V Motor line into the system power source
 directly.

If the above power management is used, all signal lines that will be
electrically active in the host system while the HDD is disconnected
from power line shall be isolated by three-state line drivers.
Internal leakage through ESD protection circuit may pull down LPUL
(least positive up level) of logic signal specification.

Use both lines parallel, for regular HDD applications.