Hard Drive: FUJITSU: M1624TAU 2111MB 3.5"/SL ATA2 FAST

M 1 6 2 4 T A U    FUJITSU
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders    6237| 3298|     |
Capacity form/unform  2111/      MB        Heads           3|   16|     |
Seek time   / track  11.0/ 3.0 ms          Sector/track     |   63|     |
Controller           IDE / ATA2 FAST/ENHA  Precompensation
Cache/Buffer           128 KB              Landing Zone
Data transfer rate    7.700 MB/S int       Bytes/Sector      512
                     16.700 MB/S ext PIO4
Recording method                                    operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C                 |
Power: sleep              W     Humidity     %                 |
       standby            W     Altitude    km                 |
       idle               W     Shock        g                 |
       seek           4.9 W     Rotation   RPM      5400
       read/write         W     Acoustic   dBA        35
       spin-up            W     ECC        Bit
                                MTBF         h     500000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

FUJITSU M163X/162XTAU JUMPER SETTING

                        Jumper
               +Power-----2-6----------------------+
               |xxxxxxxx  ooo ooooooooo oooooooooo |
               |XXXXXXXX  ooo oooooooooooooooooooo |
               |1         1 5                      |
               +---------------Interface-----------+

Jumpers

FUJITSU M163X/162XTAU JUMPER SETTING

Jumper Setting
==============

   2   6
   X o o
   X o o  MASTER (default)
   1   5

   2   6
   o X o
   o X o  SLAVE
   1   5

   2   6
   xxx o
   o o o  CABLE SELECT  Cable Select Mode gives an alternative method
   1   5                by which the drive may be set to MASTER or
                        SLAVE. A special cable is needed to implement
                        this feature and ahould only be used by BOTH
                        drives.

Install

FUJITSU M163X/162XTAU JUMPER SETTING

Notes On Installation
=====================

Grounding
---------
Sufficient grounding will be provided for correct operation when
the drive is screwed into an electrically grounded frame.

Orientation
-----------
The drive may be installed in one of three orientations; PCA down
or on either edge.

     horizontally             vertically
   +-----------------+   +--+             +--+ +------------------+
   |                 |   |  +-----+ +-----+  | |                  | x
   |                 |   |  |     | |     |  | x+----------------+x
 +-+-----------------+-+ |  |     | |     |  | ||x              x||
 +---------------------+ |  |     | |     |  | ||  x          x  ||
                         |  |     | |     |  | ||    x      x    ||
      x           x      |  |     | |     |  | ||      x  x      ||
 +------x------x-------+ |  +-----+ +-----+  | ||       xx       ||
 +-+------x--x-------+-+ +--+             +--+ ||     x    x     ||
   |       xx        |                         ||   x        x   ||
   |     x    x      |                         || x            x ||
   +---x--------x----+                         |x                x|
     x            x                           x++----------------++x
      UNACCEPTABLE!                                UNACCEPTABLE!
      Never install PC board on the Top!

Cooling
-------
Allow space above and below the drive to provide for adequate air
flow. Fan cooling is recommended. The disk enclosure temperature,
measured at top center, should never exceed 60*C.

Mounting screw fixing
---------------------
When the mounting screw holes on the side of the drive are used, then
use only the two pairs of outer holes. Do not use the center hole in
conjunction with only one of the outer holes. The screw must not
penetrate the drive.
Screws: 6-32UNC