TRANSEND SIXTY-SEVEN modem/telephone/ISDN Settings and Configuration

TRANSEND CORPORATION

TRANSEND SIXTY-SEVEN

Card Type	Modem
Chip Set	Unidentified
I/O Options	Line in (2), DTE port, power jack
Maximum Modem Rate	67.2Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103A/212A ITU-T V34, V.32bis, V.32, V.22bis, V.8, V.13, V.14, V.24, V.25
Fax Modulation Protocol	ITU-T V.17, V.27ter, V.29, V.21
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	External

CONNECTIONS
Function	Label		Function		Label
Power Jack		CN1		Network port		CN4
Line 1 in		CN2		DTE port (25-pin serial connector)		CN5
Line 2 in		CN3		Power switch		SW1

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
TD	Green	Blinking	Modem transmitting data
TD	Green	Off	Modem not transmitting data
RD	Green	Blinking	Modem is receiving data
RD	Green	Off	Modem is not receiving data
CD	Green	On	Carrier signal detected or CD override is on
CD	Green	Off	Carrier signal not detected
CS	Green	On	CTS signal is high
CS	Green	Off	CTS signal is low
RS	Green	On	RTS signal is high
RS	Green	Off	RTS signal is low
TR	Green	On	Modem is receiving DTR signal/DTR override is on
TR	Green	Off	Modem is not receiving DTR signal
OH1	Green	On	Line 1 is off-hook
OH1	Green	Off	Line 1 is on-hook
OH2	Green	On	Line 2 is off-hook
OH2	Green	Off	Line2 is on-hook
TST/NMS	Red	On	Loopback test in progress
TST/NMS	Green	On	Modem controlled by Network Management System

SUPPORTED COMMAND SET

Basic AT Commands

AT, +++, A/

E, F, M, O, P, T, V, W, X, Y, Z

&G, &P, &T, &W, &X, &Y, &Z

Extended AT command set

\A, \B, \C, \G, \K, \T, \V, \X

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S22, S25, S26

Note: See MHI Help File for full command documentation.

PROPRIETARY AT COMMAND SET

ANSWER
Type:	Immediate
Format:	AT [cmds] A
Description:	Enables answer mode, the modem goes off-hook
Command	Protocol
A0	Connect to line as answer modem
A1	Connect to line as originate modem
A2	Connect to both lines as originate modem

ANSWER MODE
Type:	Configuration
Format:	AT [cmds] R [cmds]
Description:	Allows modem to switch to answer mode after dialing

CLEAR TO SEND (CTS)
Type:	Configuration
Format:	AT [cmds] &Rn [cmds]
Description:	Selects CTS options
Command	Mode
&R0	Normal CTS mode
&R1	CTS forced high.
&R2	CTS follows DCD
&R9	CTS equals RTS

COMMUNICATION PROTOCOLS
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the communication protocol for data calls
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.
Command	Protocol
B0	Auto selection
B1	ITU-T V.21
B2	Bell 103J
B3	Bell 212A
B5	V.22bis
B11	V.32bis
B12	V.34

CONFIGURATION PROFILES
Type:	Immediate
Format:	AT [cmds] &Vn [cmds]
Description:	Displays active and stored configuration profiles
&V0	Display received signal status
&V1	Display active profile

DATA CARRIER DETECT (DCD)
Type:	Configuration
Format:	AT [cmds] &Cn [cmds]
Description:	Selects whether the DCD option is enabled or disabled
Command	Function
&C0	DCD enabled
&C1	DCD enabled after carrier signal detected
&C2	DCD goes off during disconnection
&C3	DCD follows V.25bis recommendation

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR high only while modem is handshaking or connected
&S2	DSR off for 5 seconds after disconnect
&S3	DSR follows off-hook

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Command	Function
&D0	DTR forced high
&D1	DTR toggle causes online command mode
&D2	Modem disconnects after losing DTR
&D3	Resets when DTR turns off

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
Dn	Dial telephone number n
Dn%passwd	Dial telephone number n and send password
D[1] [2]	Dial two telephone numbers and modifiers

ERROR CONTROL
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Sets error control for connections at 1200bps and higher
Command	Mode
&M0	Asynchronous mode
&M1	Synchronous connect mode and asynchronous off-line command mode.
&M2	Synchronous connect mode and asynchronous off-line command mode and set DTR high.
&M3	Synchronous connect mode
&M4	Synchronous connect mode and V.25bis autodialer with BISYNC protocol
&M5	Synchronous connect mode and V.25bis autodialer with SDLC protocol
&M6	Synchronous connect mode and V.25bis asynchronous off-line command mode.

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
&F0	Factory profile 0
&F1	Factory profile 1
&F2	Factory profile 2
&F3	Factory profile 3
&F4	Factory profile 4
&F5	Factory profile 5
&F6	Factory profile 6
&F7	Factory profile 7

HOOK CONTROL
Type:	Immediate
Format:	AT [cmds] Hn [cmds]
Description:	Selects whether the modem is on-hook or off-hook
Command	Function
H0	Modem commanded to go on-hook (hang-up)
H1	Modem commanded to go off-hook (pick-up)
H2	Normal hang up enabled
H3	Fast hang up enabled

LINE TYPE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Selects line type
Command	Line Type
&L0	2-wire switched line
&L1	2-wire leased line
&L2	4-wire leased line

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports four digit product code
I1	Reports CDC volume of EPROM
I3	Reports product version number
I4	Reports compatibility mode
I5	Reports reason for disconnect

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE
Command	Function
Q0	Result code sending enabled
Q1	Result code sending disabled
Q2	Result code sending only in originate mode

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

 

EXTENDED AT COMMAND SET

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Range:	1-255
Unit:	20ms
Description:	Sends break to modem

AT COMMAND SET
Type:	Configuration
Format:	AT [cmds] *NTn [cmds]
Description:	Enables/disables AT command set.
Command	Function
*NT0	AT command set disabled
*NT1	AT command set enabled

AUTOMATIC RATE ADAPTATION
Type:	Configuration
Format:	AT [cmds] %Rn [cmds]
Description:	Enables/disables automatic rate adaptation
Command	Function
%R0	Automatic rate adaptation disabled
%R1	Automatic rate adaptation enabled with low BER
%R2	Automatic rate adaptation enabled with medium BER
%R3	Automatic rate adaptation enabled with high BER

AUTOREDIAL
Type:	Configuration
Format:	AT [cmds] -Rn [cmds]
Description:	Autoredials.

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall-forward
Command	Function
%E0	Auto-retrain disabled
%E1	Auto-retrain enabled

BILATERAL DIGITAL LOOP
Type:	Configuration
Format:	AT [cmds] *DGn [cmds]
Description:	Enables/disables bilateral digital loop.
Command	Function
*DG0	Disables bilateral digital loop
*DG1	Enables bilateral digital loop

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \Kn [cmds]
Description:	Configures action of break signal
Command	Function
\K1	Send a break after de-storing data buffers
\K2	Break sent immediately
\K3	Buffered data sent before break signal

BUSY MODE
Type:	Configuration
Format:	AT [cmds] :Un [cmds]
Description:	Enable/disable busy mode.
Command	Function
:U0	Busy mode disable
:U3	Busy mode enable

CALL BACK
Type:	Configuration
Format:	AT [cmds] \Sn [cmds]
Description:	Enables/disables callback
Command	Function
\S0	Callback enabled
\S1	Callback disabled

CALL DISREGARD
Type:	Configuration
Format:	AT [cmds] *IC [cmds]
Description:	Disregards incoming call.

CARRIER LOSS
Type:	Configuration
Format:	AT [cmds] -Pn [cmds]
Description:	Sets disconnect due to carrier loss.
Command	Function
-P0	Disconnect by rapid carrier loss (8 seconds)
-P1	Disconnect by normal carrier loss (45 seconds)

CHANNEL
Type:	Configuration
Format:	AT [cmds] -An [cmds]
Description:	Selects transmission channel.
Command	Function
-A0	ATX channel selected
-A1	BTX channel selected

CLEARDOWN DISCONNECT
Type:	Configuration
Format:	AT [cmds] -Fn [cmds]
Description:	Enable/disable cleardown disconnect.
Command	Function
-F0	Cleardown disconnect disabled
-F1	Cleardown disconnect enabled

CODED RESPONSE
Type:	Configuration
Format:	AT [cmds] *RCn [cmds]
Description:	Selects coded response speed
Command	Function
*RC0	15 - 4800bps; 18 - 9600bps
*RC1	11 - 4800bps; 12 - 9600bps

COMMAND STATE
Type:	Immediate
Format:	AT [cmds] :Mn [cmds]
Description:	Enable/disable command state.
Command	Function
:M0	Command state disabled
:M1	Command state enabled

COMMAND STATE
Type:	Configuration
Format:	AT [cmds] :Sn [cmds]
Description:	Selects number of retrains.
Command	Function
:S0	AT command compatible after reset
:S1	V.25bis compatible after reset

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 or bilateral V.42bis compression enabled
%C2	V.42bis on transmitted data enabled
%C3	V.42bis on received data enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	LAPM mode enabled
\N5	LAPM or normal mode enabled
\N6	LAPM or MNP mode enabled
\N7	LAPM, MNP, or normal mode enabled

CONNECTION SPEED LOWER LIMIT
Type:	Configuration
Format:	AT [cmds] %L [cmds]
Description:	Sets slowest allowed connection speed.
Command	Function
%L0	Disabled
%L1	Disabled
%L2	Set minimum connect speed to 1200bps.
%L3	Set minimum connect speed to 2400bps.
%L4	Set minimum connect speed to 4800bps.
%L5	Set minimum connect speed to 9600bps uncoded.
%L6	Set minimum connect speed to 9600bps.
%L7	Set minimum connect speed to 7200bps
%L8	Set minimum connect speed to 12.0Kbps.
%L9	Set minimum connect speed to 14.4Kbps.
%L11	Set minimum connect speed to 16.8Kbps.
%L12	Set minimum connect speed to 19.2Kbps.
%L13	Set minimum connect speed to 21.6Kbps.
%L14	Set minimum connect speed to 24Kbps.
%L15	Set minimum connect speed to 26.4Kbps.
%L16	Set minimum connect speed to 28.8Kbps.
%L17	Set minimum connect speed to 31.2Kbps.
%L18	Set minimum connect speed to 33.6Kbps.

CONNECTION SPEED UPPER LIMIT
Type:	Configuration
Format:	AT [cmds] %Bn [cmds]
Description:	Sets fastest allowed connection speed.
Command	Function
%B0	Use DTE speed.
%B1	Set maximum connect speed to 300bps.
%B2	Set maximum connect speed to 1200bps.
%B3	Set maximum connect speed to 2400bps.
%B4	Set maximum connect speed to 4800bps.
%B5	Set maximum connect speed to 9600bps uncoded.
%B6	Set maximum connect speed to 9600bps.
%B7	Set maximum connect speed to 7200bps
%B8	Set maximum connect speed to 12.0Kbps.
%B9	Set maximum connect speed to 14.4Kbps.
%B11	Set maximum connect speed to 16.8Kbps.
%B12	Set maximum connect speed to 19.2Kbps.
%B13	Set maximum connect speed to 21.6Kbps.
%B14	Set maximum connect speed to 24Kbps.
%B15	Set maximum connect speed to 26.4Kbps.
%B16	Set maximum connect speed to 28.8Kbps.
%B17	Set maximum connect speed to 31.2Kbps.
%B18	Set maximum connect speed to 33.6Kbps.

CONNECTION SPEED UPPER LIMIT
Type:	Configuration
Format:	AT [cmds] :Bn [cmds]
Description:	Sets fastest allowed connection speed.
Command	Function
:B0	Use DTE speed.
:B1	Set maximum connect speed to 300bps.
:B2	Set maximum connect speed to 1200bps.
:B3	Set maximum connect speed to 2400bps.
:B4	Set maximum connect speed to 4800bps.
:B5	Set maximum connect speed to 9600bps uncoded.
:B6	Set maximum connect speed to 9600bps.
:B7	Set maximum connect speed to 7200bps
:B8	Set maximum connect speed to 12.0Kbps.
:B9	Set maximum connect speed to 14.4Kbps.
:B11	Set maximum connect speed to 16.8Kbps.
:B12	Set maximum connect speed to 19.2Kbps.
:B13	Set maximum connect speed to 21.6Kbps.
:B14	Set maximum connect speed to 24Kbps.
:B15	Set maximum connect speed to 26.4Kbps.
:B16	Set maximum connect speed to 28.8Kbps.
:B17	Set maximum connect speed to 31.2Kbps.
:B18	Set maximum connect speed to 33.6Kbps.

CT108 FUNCTION DTR
Type:	Immediate
Format:	AT [cmds] :Dn [cmds]
Description:	Selects CT108 function DTR.
Command	Function
:D0	CT108/2
:D1	CT108/1

CT108 FUNCTION DTR
Type:	Immediate
Format:	AT [cmds] :Dn [cmds]
Description:	Selects CT108 function DTR.
Command	Function
:D0	CT108/2
:D1	CT108/1

DATA MODUALTION
Type:	Configuration
Format:	AT [cmds] *MMn [cmds]
Description:	Selects data modulation protocol
Command	Function
*MM0	Automatic modulation selection
*MM1	ITU-T V.21
*MM2	Bell 103J
*MM3	Bell 212A
*MM5	ITU-T V.22bis
*MM11	ITU-T V.32bis
*MM12	ITU-T V.34

DATA RATE SELECT SIGNAL
Type:	Configuration
Format:	AT [cmds] *FBn [cmds]
Description:	Selects signal response.
Command	Function
*FB0	Ignores data rate select signal
*FB1	Signal transition causes DTE speed fallback

DIAL ON MANUAL CONNECTION
Type:	Configuration
Format:	AT [cmds] %Mn [cmds]
Description:	Dial on manual connection enable/disable
Command	Function
%M0	Dial on manual connection disabled
%M1	Dial on manual connection enabled

DIAL STORED NUMBER
Type:	Configuration
Format:	AT [cmds] *Aun [cmds]
Range:	0-9
Description:	Dials number stored at location n when modem is in command state and the DTR signal transitions.

DIAL TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] *TDn [cmds]
Range:	9-30
Unit:	-1dBm
Description:	Sets transmission level

DISCONNECT
Type:	Configuration
Format:	AT [cmds] -Hn [cmds]
Description:	Enable/disable cleardown disconnect.
Command	Function
-H0	Disconnect by data and DCD loss disabled
-H1	Disconnect by carrier loss disabled
-H2	Disconnect by 4 minute data loss enabled
-H3	Disconnect by DCD and data loss enabled

DISCONNECT BUFFER DELAY
Type:	Configuration
Format:	AT [cmds] %D [cmds]
Range:	0-255
Unit:	1 second
Description:	Sets disconnect buffer delay; %D0 will disable this function.

DTE SPEED
Type:	Configuration
Format:	AT [cmds] -Un [cmds]
Range:	1200-46800
Unit:	1bps
Description:	Sets DTE speed

FAST TRAIN
Type:	Configuration
Format:	AT [cmds] *FTn [cmds]
Description:	Enables/disables fast train.
Command	Function
*FT0	Fast train disabled
*FT1	Fast train enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	DTE flow control disabled
\Q1	DTE bi-directional XON/XOFF flow control enabled
\Q2	CTS flow control by DCE enabled
\Q3	Bi-directional RTS/CTS flow control enabled
\Q4	DCE flow control disabled
\Q5	Unidirectional XON/XOFF flow control by DCE enabled
\Q6	CTS flow control to DTE enabled
\Q7	CTS flow control to DTE disabled

INTERFACE SPEED
Type:	Configuration
Format:	AT [cmds] -Vn [cmds]
Description:	Enable/disable interface speed.
Command	Function
-V0	Interface speed disabled
-V1	Interface speed enabled

LAPM DETECTI0N PHASE CONTROL
Type:	Configuration
Format:	AT [cmds] \Mn [cmds]
Description:	Enables/disables LMNP detection phase control
Command	Function
\M0	LAPM detection phase control disabled
\M1	LAPM detection phase control enabled

LEASED LINE
Type:	Configuration
Format:	AT [cmds] *LB [cmds]
Description:	Return to leased line from dial backup.

LEASED LINE TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] *TLn [cmds]
Range:	9-30
Unit:	-1dBm
Description:	Sets transmission level

LIN CURRENT DISCONNECT
Type:	Configuration
Format:	AT [cmds] *LCn [cmds]
Description:	Selects length of disconnect.
Command	Function
*LC0	Line current disconnect disabled
*LC1	Short (8ms) disconnect enabled
*LC2	Long (90ms) disconnect enabled

LOCAL ANALOG LOOPBACK SIGNAL
Type:	Configuration
Format:	AT [cmds] *Lan [cmds]
Description:	Selects signal response.
Command	Function
*LA0	Ignores local analog loopback signal
*LA1	DTE commanded local analog loopback

LOOPBACKS
Type:	Configuration
Format:	AT [cmds] -In [cmds]
Description:	Enable/disable loopbacks.
Command	Function
-I0	Interface loopbacks disabled
-I1	CT141 - LAL enabled
-I2	CT140 - RDL enabled
-I3	CT140, CT141 enabled
-I4	CT140 with inverted polarity enabled
-I5	CT140 with inverted polarity, CT141 enabled

MONITOR LEASED LINE
Type:	Configuration
Format:	AT [cmds] :Tn [cmds]
Description:	Selects time in minutes that leased line is monitored.
Command	Function
:T0	5 minutes
:T1	15 minutes
:T2	30 minutes
:T3	60 minutes

OPTIONS
Type:	Configuration
Format:	AT [cmds] *Ron [cmds]
Description:	Restore/retain options.
Command	Function
*RO0	Retains options at disconnect
*RO1	Restores options at disconnect

ORIGINATE/ANSWER
Type:	Configuration
Format:	AT [cmds] *ORn [cmds]
Description:	Selects originate of forced answer mode
Command	Function
*OR0	Originate mode
*OR1	Answer mode

PASSWORD
Type:	Configuration
Format:	AT [cmds] %P [cmds]
Description:	Programs, displays and clears password
Command	Function
%P=passwd	Programs remote configuration password
%P?	Reports remote configuration password of local modem
%P=(blank)	Clears password

RATE NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *RR [cmds]
Description:	Sets negotiation speed.
Command	Function
*RR0	Set negotiation speed to 2400bps.
*RR1	Set negotiation speed to 4800bps.
*RR2	Set negotiation speed to 7200bps.
*RR3	Set negotiation speed to 9600bps
*RR4	Set negotiation speed to 12.0Kbps.
*RR5	Set negotiation speed to 14.4Kbps.
*RR6	Set negotiation speed to 16.8Kbps.
*RR7	Set negotiation speed to 19.2Kbps.
*RR8	Set negotiation speed to 21.6Kbps.
*RR9	Set negotiation speed to 24Kbps.
*RR10	Set negotiation speed to 26.4Kbps.
*RR11	Set negotiation speed to 28.8Kbps.
*RR12	Set negotiation speed to 31.2Kbps.
*RR13	Set negotiation speed to 33.6Kbps.

REMOTE CONFIGURATION
Type:	Configuration
Format: