WEBJET 128 modem/telephone/ISDN Settings and Configuration

Card Type	ISDN TA
Chip Set	Unidentified
I/O Options	RJ-45 ISDN BRI U interface, 9-pin DTE port, power, microphone in, speaker out
ISDN Rate	230.4Kbps
ISDN Modulation Protocol	PPP, MLPPP, V.120
Error Correction/Compression	Unidentified
Data Bus	External

CONNECTIONS
Function	Label	Function	Label
ISDN BRI interface (RJ-45)	CN1	9-pin DTE port	CN4
Microphone in	CN2	Power	CN5
Speaker out	CN3	Power switch	SW1

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
DATA	Unidentified	On	DTR is high
DATA	Unidentified	Blinking	Serial data transfer active
DATA	Unidentified	Off	Serial data transfer not in progress
B1	Unidentified	On	B-channel 1 data call connected
B1	Unidentified	Off	No activity on B-channel 1
B2	Unidentified	On	B-channel 2 data call connected
B2	Unidentified	Off	No activity on B-channel 2
PWR	Unidentified	On	Power is on
PWR	Unidentified	Off	Power is off

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, E, Q, V, W, X

&F, &V

S Registers

S0, S2, S3, S4, S5, S7, S25

Note: See MHI Help File for full command documentation.

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &M n [cmds]
Description:	Selects communications mode
Command	Mode
&M0	Asynchronous mode
&M1	Synchronous connect mode and asynchronous off-line command mode.
&M2	Synchronous connect mode and asynchronous off-line command mode and set DTR high.

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Q n [cmds]
Description:	Selects communications mode options
Command	Mode
&Q0	Asynchronous mode, serial port speed follows connect speed.
&Q1	Asynchronous off-line command mode and synchronous connect mode.
&Q2	Asynchronous off-line command mode - modem autodials first number in directory, then synchronous connect mode.
&Q3	Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR.
&Q4	Auto-synchronous mode
&Q5	Error correction mode

DATA CARRIER DETECT (DCD)
Type:	Configuration
Format:	AT [cmds] &C n [cmds]
Description:	Selects whether the DCD option is enabled or disabled
Command	Function
&C0	DCD enabled
&C1	DCD enabled after carrier signal detected
&C2	DCD enabled when on-line, low at loss of carrier, enabled again at idle

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &S n [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR high only while modem is connected
&S2	DSR high only while modem is connected

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &D n [cmds]
Description:	Selects modem response to DTR
Note: The action each variant of &D causes depends on the setting of &Q
&Q Setting	&D0	&D1	&D2	&D3
&Q0, &Q5	Command 0	Command 1	Command 2	Command 4
&Q1	Command 2	Command 1	Command 2	Command 4
&Q2	Command 2	Command 2	Command 2	Command 2
Command	Function
Command 0	Modem does not respond to DTR
Command 1	Modem goes to command mode after DTR goes is off
Command 2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
Command 3	Modem is initialized after DTR goes off

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &K n [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
&K1	RTS to CTS flow control enabled
&K2	XON/XOFF flow control enabled
&K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled

HOOK CONTROL
Type:	Immediate
Format:	AT [cmds] H n [cmds]
Description:	Selects whether the modem is on-hook or off-hook
Command	Function
H0	Modem commanded to go on-hook (hang-up)

ON-LINE
Type:	Immediate
Format:	AT [cmds] O n [cmds]
Description:	Controls on-line command (data transmission) state options.
Note: The O command must be placed at the end of the command string.
Command	Function
O0	On-line command mode with no retraining enabled

PROTOCOL SELECTION
Type:	Configuration
Format:	AT [cmds] &O n [cmds]
Description:	Selects active protocol
Command	Mode
&O7	PPP, 1 x B
&O8	V.14, 1 x B
&O9	V.110, 1 x B
&O10	V.120, 1 x B
&O13	Multi Link V.120, 2 x B
&O16	GCI-speech, 2 x B
&O18	GCI-data, 2 x B
&O27	Multi Link PPP, 2 x B

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] I n [cmds]
Description:	Displays information requested
Command	Function
I0	Reports hardware identification
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports product name and software revision
I4	Reports manufacturer information
I5	Reports protocol options
I8	Reports Euro-ISDN software version

RESTORE PROFILE ON POWER-UP
Type:	Configuration
Format:	AT [cmds] &Y n [cmds]
Description:	Restores a selected profile into the active profile on power-up (hard reset).

RTS/CTS
Type:	Configuration
Format:	AT [cmds] &R n [cmds]
Description:	Command function currently unidentified

SOFT RESET
Type:	Immediate
Format:	AT [cmds] Z n [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.

STORE ACTIVE PROFILE
Type:	Configuration
Format:	AT [cmds] &W n [cmds]
Description:	Writes the values for the active profile into the non-volatile RAM

CONFIGURATION PROFILES
Type:	Immediate
Format:	AT [cmds] /S [cmds]
Description:	Displays active and stored configuration profiles

PROTOCOL SELECTION
Type:	Configuration
Format:	AT [cmds] #CH= n [cmds]
Description:	Selects active protocol
Command	Mode
#CH=7	PPP, 1 x B
#CH=8	V.14, 1 x B
#CH=9	V.110, 1 x B
î	V.120, 1 x B
#CH=13	Multi Link V.120, 2 x B
#CH=16	GCI-speech, 2 x B
#CH=18	GCI-data, 2 x B
#CH=27	Multi Link PPP, 2 x B

REMOTE NUMBER SELECTION
Type:	Configuration
Format:	AT [cmds] #REMNBRC= n [cmds]
Description:	Selects remote control number

REMOTE PASSWORD SELECTION
Type:	Configuration
Format:	AT [cmds] #PASSRC= n [cmds]
Description:	Selects remote control password

RING MODE
Type:	Configuration
Format:	AT [cmds] #RM= n [cmds]
Description:	Selects ring mode
Command	Mode
#RM0	Selects ring mode by subnumber or MSN
#RM1	Pass on call to active profile

SOFT RESET
Type:	Immediate
Format:	AT [cmds] #Z n [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.

STORED PROFILES
Type:	Immediate
Format:	AT [cmds] #V [cmds]
Description:	Displays list of stored parameters in short form

ACTIVE PROFILE
Type:	Register
Format	AT [cmds] S110= n [cmds]
Range:	0-255
Unit:	Bit-mapped
Description:	Selects active profile

AUTOBAUD
Type:	Register
Format	AT [cmds] S124= n [cmds]
Description:	Enables/disables autobaud function
Command	Function
S124=0	Autobaud disabled
S124=1	Autobaud enabled

BIT-MAPPED REGISTER S112
Format:	AT [cmds] S112= n [cmds]
Range:	Unidentified
Unit:	Bit-mapped
Description:	Controls ring message format
Bit	Value	Function
0	0 1	Standard AT RING message format (RING) Extended AT RING message format (RING J
1	0 1	Extended result codes disabled Extended result codes enabled
2	0	Not used
3	0 1	Standard AT format Extended AT format
6 - 4	0	Not used
7	0 1	Additional service messages disabled Additional service messages enabled

DTR COMMAND
Type:	Register
Format	AT [cmds] S123= n [cmds]
Description:	Enables &D command
Command	Function
S123=0	&D enabled for DTR functions
S123=1	DTR ingnored. &D command disabled

EXTENDED RESULT CODES
Type:	Register
Format	AT [cmds] S95= n [cmds]
Range:	0-255
Unit:	Bit-mapped
Description:	Works in combination with the W n command to enable extended result codes. Features enabled by S95 take precedence over the options selected by W n .
Bit	Value	Function
0	0 1	CONNECT result code reports DTE speed. CONNECT result code reports line speed instead DTE speed.
1	0 1	Verbose CONNECT result codes display DTE or line speed only. Adds "/ARQ" to all verbose CONNECT result codes except "NONE."
2	0 1	CARRIER result codes disabled. CARRIER result codes enabled.
3	0 1	PROTOCOL result codes disabled. PROTOCOL result codes enabled.

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] S121= n [cmds]
Range:	0-255
Description:	Sets values in active profile to values found in the default profile
Command	Function
S121=0	Retrieve factory settings and restart
S121=255	Disabled

FLOW CONTROL
Type:	Register
Format	AT [cmds] S39? [cmds]
Description:	Displays the current flow control
Value	Meaning
0	Flow control disabled
3	RTS/CTS flow control enabled
4	XON/XOFF flow control enabled

PROTOCOL SERVICE
Type:	Register
Format	AT [cmds] S111= n [cmds]
Description:	Selects options for protocol service
Command	Function
1	Voice service
2	Data modem service
3	Raw data service
4	Group 3 fax service
5	V.14
7	PAD service
8	V.120 service
10	Synchronous relay service

RING MESSAGE TIMER
Type:	Register
Format	AT [cmds] S117= n [cmds]
Range:	0-255
Unit:	1 second
Description:	Maximum duration allowed between two consecutive RING messages
Note: S117=0 allows for a single RING message only

SERIAL ASYNCHRONOUS RATE & CLOCK SELECTION
Type:	Register
Format	AT [cmds] S114= n [cmds]
Description:	Selects sserial asynchronous speed & clock selection
Command	Function
S114=0	External clock source
S114=1	1200bps
S114=2	2400bps
S114=3	300bps
S114=4	4800bps
S114=7	7200bps
S114=9	9600bps
S114=12	1200bps
S114=14	14.400bps
S114=19	19.2Kbps
S114=24	2400bps
S114=28	28.8Kbps
S114=38	38.4Kbps
S114=48	4800bps
S114=20	57.6Kbps
S114=72	7200bps
S114=75	75bps
S114=96	9600bps
S114=115	115.2Kbps
S114=255	Internal clock source

SOFT RESET
Type:	Immediate
Format:	AT [cmds] S122= n [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.
Command	Function
S122=0	Restore setting
S122=255	Disabled