INTERLOGIC INDUSTRIES
A104-VFM
Modem Type | Data/Fax/Voice |
Maximum Data Rate | 2400 bps |
Maximum Fax Rate | 9600 bps |
Data Bus | PC/104 |
Fax Class | Unidentified |
Data Modulation Protocol | Bell 103A & 212A, CCITT V.22 |
Fax Modulation Protocol | Unidentified |
Error Correction/Compression | CCITT V.42 & V.42bis, MNP 5 |
CONNECTIONS | |||
Purpose | Location | Purpose | Location |
Line out | CN1 | Speaker jack | SPKR |
Line in | CN2 |
COM PORT SETTINGS | ||||
COM | JU1 | JU2 | JU3 | JU4 |
COM1 | Open | Open | Closed | Open |
COM2 | Closed | Open | Open | Closed |
COM3 | Open | Closed | Closed | Open |
COM4 | Closed | Closed | Open | Closed |
CONNECTOR JP1 | |
Purpose | Location |
Pair 2 Tip & Ring | JP1 Pins 1 & 4 |
Pair 1 Tip & Ring | JP1 Pins 2 & 3 |
S14 -BIT MAPPED CONFIGURATION REGISTER | |||
Value Range: | Bit-mapped | ||
Default: | 1 | ||
Type: | Read/Write | ||
In Stored Profile?: | Yes | ||
Description: | Bit Mapped Configuration Register | ||
Bit | Value | Function | |
0 | 0 | Not used | |
1 | í 10 | Enable: Command echo (E1) Disable: Command echo (E0) | |
2 | í 01 | Enable: Result codes (Q0) Disable: Result codes (Q1) | |
3 | í 10 | Set result codes to word (V1) Set result codes to digit (V0) | |
4 | 0 | Not used | |
5 | í 10 | Set to Pulse dial (P) Set to Tone Dial (T) | |
6 | 0 | Not used | |
7 | í 10 | Enable: Originate mode Enable: Answer mode |
S21 -BIT MAPPED CONFIGURATION REGISTER | |||
Value Range: | Bit-mapped | ||
Default: | 1 | ||
Type: | Read/Write | ||
In Stored Profile?: | Yes | ||
Description: | Bit Mapped Configuration Register | ||
Bit | Value | Function | |
0 | 0 | Not used | |
1 | 0 | Not used | |
2 | 0 | Not used | |
3 & 4 | í 0001 10 11 | Sets modem to ignore DTR (&D0) ON-to-OFF transition on DTR forces the modem to enter the command mode (&D1) ON-to-OFF transition on DTR forces the modem to hang up (&D2) ON-to-OFF transition on DTR forces the modem to reset (&D3) | |
5 | í 01 | Enable: DCD always ON (&C0) DCD checks the actual state of the data carrier (&C1) | |
6 | 0 | Not used | |
7 | í 01 | Disable: Long Space Disconnect (Y0) Enable: Long Space Disconnect (Y1) |
S22 -BIT MAPPED CONFIGURATION REGISTER | |||
Value Range: | Bit-mapped | ||
Default: | 1 | ||
Type: | Read/Write | ||
In Stored Profile?: | Yes | ||
Description: | Bit Mapped Configuration Register | ||
Bit | Value | Function | |
0 & 1 | í 1000 01 11 | Speaker volume set to medium (l1) Speaker volume set to low (l0) Speaker volume set to low (l1) Speaker volume set to high (l3) | |
2 & 3 | í 0100 10 11 | Enable: Speaker on until carrier detected (M1) Disable: Speaker (M0) Enable: Speaker always on (M2) Enable: Speaker on until carrier detected but Off during dialing (M3) | |
4 & 5 & 6 | í 111000 100 101 110 | Enable: fourth extended result code set (X4) Enable: basic result code set (x0) Enable: first extended result code set (X1) Enable: second extended result code set (X2) Enable: third extended result code set (X3) | |
7 | í 01 | Set Make/Break ratio is 39/61 for USA (&P0) Set Make/Break ratio is 33/67 for UK/HK (&P1) |
S23 - BIT MAPPED CONFIGURATION REGISTER | |||
Value Range: | Bit-mapped | ||
Default: | 1 | ||
Type: | Read/Write | ||
In Stored Profile?: | Yes | ||
Description: | Bit Mapped Configuration Register | ||
Bit | Value | Function | |
0 | í 10 | Disable: Accept request from remote modem for a remote digital loopback (&T5) Enable: Accept request from remote modem for a remote digital loopback (&T4) | |
1 & 2 & 3 | 000 001 010 011 100 101 | 300 bps 600 bps 1200 bps 2400 bps 4800 bps 9600 bps | |
4 & 5 | 00 01 10 11 | Enable: Even parity. Enable: Space parity. Enable: Odd parity. Enable: Mark parity. | |
6 | í 0001 10 11 | Disable: Guard tone (&G0) Enable: 550 Hz guard tone (&G2) Enable: 1800 Hz guard tone (&G2) Not used |
S27 -BIT MAPPED CONFIGURATION REGISTER | |||
Value Range: | Bit-mapped | ||
Default: | 1 | ||
Type: | Read/Write | ||
In Stored Profile?: | Yes | ||
Description: | Bit Mapped Configuration Register | ||
Bit | Value | Function | |
0 | 0 | Not used | |
1 | 0 | Not used | |
2 | 0 | Not used | |
3 | 0 | Not used | |
4 | 0 | Not used | |
5 | 0 | Not used | |
6 | í 10 | Enable: Bell 212A with 1200bps, Bell 103 with 300bps (B1) Enable: CCITT V.22 with 1200bps; V.21 with 300bps (B0) | |
7 | 0 | Not used |