EVEREX SYSTEMS,INC.

EVERCOM INTERNAL MODEM

Card Type	Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	2400bps
Data Bus	8-bit ISA
Data Modulation Protocol	Bell 103/212A ITU-T V.22, V.22bis

CONNECTIONS
Function	Label		Function		Label
Line in		CN1		Line out		CN2

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í DCD normal	SW1/4	Off
DCD forced high	SW1/4	On
í RJ11, RJ14, RJ41S, or RJ45 jack type	SW1/5	Off
RJ12 or RJ13	SW1/5	On

SERIAL PORT ADDRESS
Setting	SW1/1	SW1/2
í COM1 (3F8h)	Off	Off
COM2 (2F8h)	On	Off
COM3 (3E8h)	Off	On
COM4 (2E8h)	On	On

INTERRUPT SELECTION
SETTING	SW1/3
IRQ2 (IBM PC/XT) or IRQ9 (IBM AT)	On
í IRQ3 or IRQ4	Off

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘Comma’, A/

A, B, D, E, F, H, L, M, O, Q, S, V, X, Y, Z

&D, &G, &L, &P, &T

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S20, S22, S23, S27

Note: See MHI Help file for full command documentation.

BIT-MAPPED REGISTER S21
Format		AT [cmds] S21=n [cmds]
Default:		0
Range:		0-184
Unit:		Bit-mapped
Description:		Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function.
Bit	Value	Function
2 - 0	0	Not used
4, 3	í 00 01 10 11	DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR
5	0 í 1	DCD forced high DCD normal
6	0	Not used
7	í 0 1	Long space disconnect function disabled Long space disconnect function enabled

BIT-MAPPED REGISTER S22
Format		AT [cmds] S22=n [cmds]
Default:		118
Range:		0-255
Unit:		Bit-mapped
Description:		Controls speaker volume and controls, dial mode, call progress, connect message, and pulse dial make/break ratio.
Bit	Value	Function
1, 0	00 01 í 10 11	Low volume Low level volume Medium level volume High level volume
3, 2	00 í 01 10 11	Speaker off Speaker off on carrier Speaker always on Speaker on during handshake
4	0 í 1	Blind dial Wait for dial tone then proceed with the call
5	0 í 1	Call progress disabled Call progress enabled
6	0 í 1	‘CONNECT’ message only ‘CONNECT XXXX’ message
7	í 0 1	39/61ms at 10pps (North America) 33/67ms at 10pps (Europe)

BIT-MAPPED REGISTER S27
Format		AT [cmds] S27=n [cmds]
Default:		64
Range:		0-66
Unit:		Bit-mapped
Description:		Selects line type, and ITU-T/Bell modes.
Bit	Value	Function
1, 0	00	Not used
2	í 0 1	Switched line Leased line
5 - 3	000	Not used
6	0 í 1	ITU/T mode Bell mode

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Reports current speed, data bits, and parity

Share and Enjoy

Tags

guides information FAQ manuals articles essays