E-TECH RESEARCH, INC.
C1414CX PCMCIA
Card Type | Modem (asynchronous) |
Chipset | Unidentified |
Maximum Onboard Memory | SRAM (amount is unidentified) |
Maximum Data Rate | 14.4Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | PCMCIA Type II |
Fax Class | Class I |
Data Modulation | Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis |
Fax Modulation | ITU-T V.17, V.21CH2, V.27ter, V.29 |
Error Correction/Compression | MNP5, V.42, V.42bis |
E-TECH-RESEARCH-INC-Modem-asynchronous-C1414CX-PCM
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z |
&C, &D, &F, &G, &P, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \V, \X, \Y, \Z |
%A, %C, %E, %G, %Q |
Special AT Commands |
-C, -J, "H, "O |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26, S30, S90, S108, S109 |
Note: See MHI documentation for complete information. |
Proprietary AT Command Set
BREAK TYPE | |||||
Type: | Configuration | ||||
Format: | AT [cmds] \Kn [cmds] | ||||
Description: | Configures action of break signal | ||||
Command | Break from DTE Reliable/Normal mode | Break from DTE Direct mode | Modem receives \B | Break from remote modem | |
\K0 | Enter command mode, do not send break to remote modem. | Send break to remote modem immediately, then enter command mode. | Buffers cleared and break sent to remote modem. | Buffers cleared and break sent to DTE. | |
\K1 | Buffers cleared and break sent to remote modem. | Send break to remote modem immediately. | Buffers cleared and break sent to remote modem. | Buffers cleared and break sent to DTE. | |
\K2 | Enter command mode, do not send break to remote modem. | Send break to remote modem immediately, then enter command mode. | Send break to remote modem immediately. | Send break to DTE immediately. | |
\K3 | Send break to remote modem immediately. | Send break to remote modem immediately. | Send break to remote modem immediately. | Send break to DTE immediately. | |
\K4 | Enter command mode, do not send break to remote modem. | Send break to remote modem immediately, then enter command mode. | Send break to remote modem with transmitted data. | Break sent with received data to the DTE. | |
\K5 | Send break with transmitted data. | Send break to remote modem immediately. | Send break to remote modem with transmitted data. | Break sent with received data to the DTE. |
DISPLAY INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested about the modem. |
Command | Function |
I0 | Displays product identification code. |
I1 | Displays ROM checksum. |
I2 | Tests and displays ROM checksum. |
I3 | Displays device set name. |
I4 | Displays modem configuration. |
SRAM BUFFER | ||
Type: | Configuration | |
Format: | AT [cmds] Kn [cmds] | |
Description: | Selects whether the modem will use its internal SRAM to buffer data. | |
Command | Function | |
K0 | SRAM buffer disabled. | |
í K1 | SRAM buffer enabled. |
TRELLIS CODING | ||
Type: | Configuration | |
Format: | AT [cmds] &Un [cmds] | |
Description: | Selects whether the modem will use trellis coding. | |
Command | Function | |
í &U0 | Trellis coding enabled. | |
&U1 | Trellis coding disabled. |