PCMCIA 14.4 FAXMODEM modem/telephone/ISDN Settings and Configuration

Card Type	Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

AUTO-RETRAIN - FALLBACK/FALLFORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall forward
Command	Function
%E0	Auto-retrain disabled
í %E1	Auto-retrain enabled
%E2	Fallback/fall forward enabled
%E3	Auto-retrain enabled but modem will disconnect if EQM reaches hang-up threshold

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	Unidentified
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type	Configuration
Format	AT [cmds] \Kn [cmds]
Default	5
Range	1-5
Description	Configures action of break signal

COMPRESSION
Type:	Configuration
Format:	AT %Cn
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
í %C3	MNP5 and V.42bis enabled

COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :En [cmds]
Description:	Controls V.32 compromise equalizer
Command	Function
:E0	Equalizer disabled
í :E1	Equalizer enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Sets connect mode
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
í \N3	Auto-reliable mode enabled
\N4	LAPM mode enabled
\N5	MNP mode enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
í \A3	MNP block size is 256 characters

MNP STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP
Command	Function
í \L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

MNP10 COMPRESSION
Type:	Configuration
Format:	AT [cmds] -Kn [cmds]
Description:	Selects MNP10 data compression from V.42 LAPM
Command	Function
-K0	MNP10 disabled
í -K1	MNP10 enabled
-K2	MNP10 enabled on originate mode only

MNP10 FALLBACK
Type:	Configuration
Format:	AT [cmds] -Qn [cmds]
Description:	Allows MNP10 to fallback to speeds slower than 4800bps
Command	Function
-Q0	MNP10 at 2400 and 1200bps disabled
í -Q1	MNP10 at 2400 and 1200bps enabled

MNP10 LINK NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *Hn [cmds]
Description:	Sets the speed at which MNP10 link negotiation will occur
Command	Function
í *H0	Link will be negotiated at highest possible speed
*H1	Link will be negotiated at 1200bps
*H2	Link will be negotiated at 4800bps

MNP10 POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] )Mn [cmds]
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
í )M0	Power level adjustment disabled
)M1	Power level adjustment enabled

REPORT LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns received line signal level

REPORT LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Reports line signal quality

TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] @Mn [cmds]
Default:	0
Range:	11-31
Unit:	-1dBm
Description:	Sets the initial signal level for transmission
Command	Function
@M0	-26dBm
@M1	-30dBm
@M2-@M10	-10dBm