5634PEW modem/telephone/ISDN Settings and Configuration

Card Type	Modem/Fax card
Chip Set	ESS
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.90
Fax Modulation Protocol	ITU-T V.17, V.27ter, V.29, V.21CH2
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	PCI

CONNECTIONS
Function	Label		Function		Label
Line in (RJ-11)		CN1		Line out (RJ-11)		CN2

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘comma’, A/

A, B, E, H, P, Q, T, V, W, X, Y, Z

&C, &P, &V, &W, &Y, &Z

Extended AT Commands

\A, \G, \L

%C

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S21, S22, S29, S32, S33

Note: See MHI Help File for full command documentation.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
í N1	Auto-mode detection enabled

AUXILIARY RELAY CONTROL
Type:	Configuration
Format:	AT [cmds] &Jn [cmds]
Description:	Enables/disables A/A1 relay driver. Not for use with RJ-11 phone lines
Command	Jack Type
í &J0	Auxiliary relay is disabled

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Selects communications mode
Command	Mode
&M0	Asynchronous mode

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Qn [cmds]
Description:	Selects communications mode options
Command	Mode
&Q0	Asynchronous mode, serial port speed follows connect speed.

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Command	Function
í &D0	DTR override
&D1	DTR toggle causes online command mode
&D2	DTR toggle causes modem to go on-hook

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &Fn [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
&F0	Restore stored profile 0 after warm reset
&F1	Restore stored profile 1 after warm reset

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	RTS/CTS & XON/XOFF flow control enabled

LINE TYPE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Command nonfunctional
Command	Line Type
&L0	Returns OK

ON-LINE
Type:	Immediate
Format:	AT [cmds] On [cmds]
Description:	Controls on-line command (data transmission) state options.
Note: The O command must be placed at the end of the command string.
Command	Function
O0	On-line command mode with no retraining enabled
O1	On-line command mode with long retrain sequence enabled
O2	On-line command mode with short retrain sequence enabled

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports hardware variation code
I2	Reports DSP firmware revision
I3	Reports modem firmware revision information
I4	Reports response programmed by modem manufacturer

SPEAKER MODE
Type:	Configuration
Format:	AT [cmds] Mn [cmds]
Description:	Selects various speaker options
Command	Function
M0	Speaker disabled
M1	Speaker enabled until carrier signal detected
M2	Speaker enabled

TEST MODES
Type:	Immediate
Format:	AT [cmds] &Tn
Description:	Selects test options
Command	Function
í &T0	End current test
&T1	Begin local analog loopback test

TRANSMIT CARRIER
Type:	Configuration
Format:	AT [cmds] Cn [cmds]
Description:	Controls the transmit carrier switching. Command nonfunctional
Command	Function
C1	Returns OK message

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Normal mode enabled
í \N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	MNP reliable mode enabled