AM2814I-V34, AM2814I-HY modem/telephone/ISDN Settings and Configuration

Card Type	Modem (synchronous/asynchronous)
Chipset	Rockwell
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A, 212A ITU-T V.22bis, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis
Fax Class	Class I & II
Data Bus	8-bit ISA
Card Size	Full height, one-third length

CONNECTIONS
Function	Label	Function	Label
Telephone line	CN1	Telephone line	CN2

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í Factory configured - do not alter	SW1/7	Off
í Factory configured - do not alter	SW1/8	Off
Note: SW1/8 may not be present on all models.

SERIAL PORT ADDRESS SELECTION
Setting	SW1/5	SW1/6
3F8h (COM1:)	On	On
2F8h (COM2:)	Off	On
3E8h (COM3:)	On	Off
í 2E8h (COM4:)	Off	Off

INTERRUPT SELECTION
Setting	SW1/1	SW1/2	SW1/3	SW1/4
í 3	Off	Off	Off	On
4	Off	Off	On	Off
5	Off	On	Off	Off
7	On	Off	Off	Off

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \G, \L, \W

%C, %E, %F, %L, %Q

Special AT Commands

#CID, :E, *H, -K, )M, @M, -Q

S-Registers

The S-registers are unidentified.

Note: See MHI help file for complete information.

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \Kn [cmds]
Description:	Configures action of break signal.
Command	Function
\K0	Enter command mode, do not send break to remote modem.
\K1	Buffers cleared and break sent to remote modem.
\K2	Enter command mode, do not send break to remote modem.
\K3	Send break to remote modem immediately.
\K4	Enter command mode, do not send break to remote modem.
\K5	Send break with transmitted data.

DIAL
Type:	Immediate
Format:	AT [cmds] D<#>;[cmds]
Description:	Dials the telephone number indicated according to any modifiers included in the string.
Command	Function
DJ	MNP10 link will be negotiated at 1200bps for this call.
DK	MNP10 power level adjustment enabled for this call.
DL	Re-dial last number.
DP	Pulse dialing enabled.
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n.
DT	Tone dialing enabled.
DW	Dialing resumed following dial tone detection.
D,	Dialing paused for amount of time specified in S8 register.
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D^	Calling tone disabled for this call.
D&	Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays product identification code.
I1	Displays ROM checksum.
I2	Tests and displays ROM checksum result.
I3	Displays firmware revision.
I6	Displays modem pump model.

PROTOCOL/SPEED
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects the protocol and speed the modem will attempt to connect at.
Command	Function
F0	Auto-detect the highest common connect speed.
F1	Select V.21 or Bell 103 at 300bps speed.
F3	Select V.23 at 75/1200bps speed.
F4	Select V.22 or Bell 212A at 1200bps speed.
F5	Select V.22bis at 2400bps speed.
F6	Select V.32 or V.32bis at 4800bps speed.
F7	Select V.32bis at 7200bps speed.
F8	Select V.32bis or V.32 at 9600bps speed.
F9	Select V.32bis at 12Kbps speed.
F10	Select V.32bis at 14.4Kbps speed.