ACER, INC.
MAGIC MP56
Card Type | Modem (asynchronous), Fax, Sound card |
Chip Set | Unidentified |
I/O Options | CD-ROM interface, game port, wavetable interface, audio line in, audio line out, microphone |
Maximum Modem Rate | 56Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Modulation Protocol | Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
Fax Modulation Protocol | ITU-T V.17, V.33, V.29, V.27ter, V.21CH2 |
Error Correction/Compression | MNP 5, V.42bis |
Fax Class | Unidentified |
Data Bus | 16-bit ISA |
CONNECTIONS | ||||||
Function | Label | Function | Label | |||
Line out | CN1 | Wavetable interface | CN6 | |||
Line in | CN2 | CD-ROM connector | CN7 | |||
Microphone | CN3 | MIDI/Game port | CN8 | |||
Audio line in | CN4 | Ring-on connector | CN9 | |||
Speaker/audio line-out | CN5 |
USER CONFIGURABLE SETTINGS | ||
Setting | Label | Position |
Flash download disabled | JP4 | Pins 1 & 2 closed |
Flash download enabled | JP4 | Pins 2 & 3 closed |
SUPPORTED COMMAND SET |
Basic AT Commands |
AT, A/ |
A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z |
&C, &F, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\K, \N |
%E, %L, %Q |
S Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, |
S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S95 |
Special Commands |
+MS |
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
AUTO-MODE DETECTION | |
Type: | Configuration |
Format: | AT [cmds] Nn [cmds] |
Description: | Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
Command | Function |
N0 | Auto-mode detection disabled |
N1 | Auto-mode detection enabled |
CLOCK SOURCE - SYNCHRONOUS TRANSMIT | |
Type: | Configuration |
Format: | AT [cmds] &Xn [cmds] |
Description: | Selects DTE transmit clock source |
Command | Function |
&X0 | Modem generates clock |
&X1 | DTE generates clock |
DATA SET READY (DSR) | |
Type: | Configuration |
Format: | AT [cmds] &Sn [cmds] |
Description: | Selects DSR options |
Command | Function |
&S0 | DSR forced high |
&S1 | DSR acts per V.25 |
DATA TERMINAL READY (DTR) | |||||
Type: | Configuration | ||||
Format: | AT [cmds] &Dn [cmds] | ||||
Description: | Selects modem response to DTR | ||||
Note: The action each variant of &D causes depends on the setting of &Q | |||||
&Q Setting | &D0 | &D1 | &D2 | &D3 | |
&Q0, &Q5, &Q6 | Command 0 | Command 1 | Command 2 | Command 3 | |
&Q1, &Q4 | Command 2 | Command 1 | Command 2 | Command 3 | |
&Q2, &Q3 | Command 2 | Command 2 | Command 2 | Command 2 | |
Command | Function | ||||
Command 0 | Modem does not respond to DTR | ||||
Command 1 | Modem goes to command mode after DTR goes is off | ||||
Command 2 | Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. | ||||
Command 3 | Modem is initialized after DTR goes off |
FLOW CONTROL | |
Type: | Configuration |
Format: | AT [cmds] &Kn [cmds] |
Description: | Enables flow control options |
Command | Function |
&K0 | Disable DTE/DCE flow control |
&K3 | RTS/CTS flow control enabled |
&K4 | XON/XOFF flow control enabled |
&K5 | Transparent XON/XOFF flow control enabled |
&K6 | Unidirectional XON/XOFF flow control enabled |
GUARD TONE | |
Type: | Configuration |
Format: | AT [cmds] &Gn [cmds] |
Description: | Commands the modem to transmit a guard tone in V.22/V.22bis |
Note: Used primarily for international data transmission | |
Command | Function |
&G0 | Guard tone disabled |
&G1 | Guard tone disabled |
&G2 | 1800Hz guard tone enabled |
REPORT INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested |
Command | Function |
I0 | Reports modem model and speed |
I1 | Reports ROM checksum |
I2 | Tests and reports ROM checksum |
I3 | Report firmware revision, model and interface type |
I4 | Report response programmed by OEM |
I5 | Report the country code parameter |
I6 | Report modem data pump model and code revision |
SPEAKER VOLUME | |
Type: | Configuration |
Format: | AT [cmds] Ln [cmds] |
Description: | Controls speaker volume |
Command | Function |
L0 | Low volume setting |
L1 | Low volume setting |
L2 | Medium volume setting |
L3 | Highest volume setting |
TRANSMIT CARRIER | |
Type: | Configuration |
Format: | AT [cmds] Cn [cmds] |
Description: | Controls the transmit carrier switching |
S(status) -REGISTERS
AUTO SYNCHRONIZATION OPTION | |
Format | AT [cmds] S19=n [cmds] |
Default: | 0 |
Range: | Unidentified |
Unit: | Unidentified |
Description: | Options are unidentified |
BIT-MAPPED REGISTER S20 | |
Format | AT [cmds] S20=n [cmds] |
Default: | 0, |
Range: | 0-253 |
Unit: | Bit-mapped |
Description: | Selects auto-sync HDLC address or BSC sync character |