 |
 |
Articles / TULARC / PC info / Hard Drives / NEWBURY DATA Hard Drives / |  |
|
|
||||
|
|
|||
|
|
|||
|
||||
|
|
||||
|
   |
|
||
|
Hard Drive: NEWBURY DATA: NDR-3170S 146MB 5.25"/FH SCSI1 SE |
|
||
|
||||
|
|
|
||
|
||||
|
|
|
|
||
|
||
|
|
|
|
||
|
|
||
|
||
|
|
|
|
||
|
||
N D R - 3 1 7 0 S NEWBURY DATA
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 1224| | |
Capacity form/unform 146/ 172 MB Heads 9| | |
Seek time / track 30.0/ 4.0 ms Sector/track 26| | |
Controller SCSI1 SINGLE-ENDED Precompensation
Cache/Buffer KB Landing Zone
Data transfer rate 1.500 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g |
seek W Rotation RPM 3600
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 20000
Warranty Month
Lift/Lock/Park YES Certificates
MAXTOR XT-3170/3280 OEM MANUAL 1011005 REV. C
+---------------------------------------------------------+ | JP81+JP82XX | PCB WITH A SHROUDED CONNECTOR +++ +XX | ++ +XX | /|| +XX | Terminators++1 +.X INTER- | \|| +XX FACE | JP94-+ ++1 +XX | +JP21 : | | || +XX | ++ JP91-+ ++1 +XX | JP87-++J2 | :| |++| | JP83-+ | | +JP44 | | +JP43 +++JP42 | | ++ ++ +-+ | +JP41 |XX | ++ |XX Power +-------------------------------------------------------+
+---------------------------------------------------------+ | JP81+JP82.. | PCB WITH A NON-SHROUDED CONNECTOR +++ |.. | ++ |.. | /|| |.. | Terminators++1 |.. | \|| |.. | ++1 |.. | +JP21 || |.. | ++ ++1 |.. | JP87-+ | | :| | | | JP83-+ | | +JP44 | | +JP43 +++JP42 | | ++ ++ +-+ | +JP41 |XX | ++ |XX J2 +-------------------------------------------------------+
: = to, i.e. JP83
:
JP87 = JP83, 84, 85, 86, 87
MAXTOR XT-3170/3280 OEM MANUAL 1011005 REV. C
Jumper Setting
==============
x = Jumpers set at factory
On both PCB's Jumpers JP41, JP43, JP21 and on PCB with a SHROUDED
CONNECTOR, JP91 through JP94 are for Manufature Test purposes, they
are NOT USER SELECTABLE and are shipped CLOSED.
JP42 Write Protect
-------------------
CLOSED Data cannot be written to the drive, only read opera-
tions can be executed.
x OPEN Allowing normal reading and writing.
Located very close to the J2 power connector and the corner of the
PCB, the write protect jumper is used to protect the data written to
the XT-3000.
JP44 Spin On Power-Up
----------------------
CLOSED The motor will start as soon as power is applied.
DRive will spin down when power is removed from drive.
On 3170/3280 OCB with a NON-SHROUDED connector, this jumper must be
installed all times.
On 3170/3280 PCB with a SHROUDED connector, this jumper, when
installed, overrides the position of JP87. On this PCB part number
it is recommended that JP44 is installed, that JP87 also be
installed.
JP81/JP82 Terminator Power --------------------------- JP81 OPEN JP82 CLOSED The terminator power is external from the SCSI bus.
JP81 CLOSED JP82 OPEN x The terminator power is internal from the drive.
JP83/84/85 SCSI ID
-------------------
+----------+-----------------------+
| SCSI ID | Jumpers |
| | JP85 | JP84 | JP83 |
+----------+-------+-------+-------+
Lowest-----|x --0 | OPEN | OPEN | OPEN |
| 1 | OPEN | OPEN | CLOSED|
| 2 | OPEN | CLOSED| OPEN |
| 3 | OPEN | CLOSED| CLOSED|
| 4 | CLOSED| OPEN | OPEN |
| 5 | CLOSED| OPEN | CLOSED|
| 6 | CLOSED| CLOSED| OPEN |
Highest----|----7 | CLOSED| CLOSED| CLOSED|
Priority +----------+-------+-------+-------+
As shipped from the factory, all jumpers are open, giving the XT-3000
a priority value/ID of zero.
In multiple SCSI device configuration, it is necessary to configure
each device with a priority. The priority identification for each
drive is determined by the three binarily weighted ID jumpers. An ID
of 7 is the highest priority in a multidevice configuration.
JP86 SCSI bus parity
---------------------
x JP86 CLOSED Enables odd parity detection.
OPEN Disables odd parity detection.
As shipped from the factory the XT-3000 detects parity. Odd parity is
always generated.
JP87 DRIVE TYPE/SPIN DELAY/START COMMAND
-----------------------------------------
On PCB with a NON-SHROUDED connector, JP87 is the DRIVE TYPE jumper.
On PCB with a SHROUDED connector, JP87 is the SPIN DELAY/START
COMMAND jumper. The SPIN DELAY/START COMMAND functions do not exist
on PCB with a NON-SHROUDED connector. There is no DRIVE TYPE jumper
on PCB with a SHROUDED connector.
JP87 PCB with a NON-SHROUDED Connector Drive Type
----------------------------------------------------
JP87 CLOSED The drive reports its type as an XT-3170 (170MB) in
the INQUIRY command.
OPEN The drive reports its type as an XT-3280 (280MB).
JP87 PCB with a SHROUDED Connector Spin Delay/Start Command
-------------------------------------------------------------
JP87 CLOSED The ID value will be used to facilitate a sequential
drive power-up process. The spindle motor turn-on,
after power-up, is delayed by approximately 13
seconds for each prioity ID level.
OPEN The drive will not spin-up until the Host issues a
Start/Stop Command (1Bh) with the Start Bit = 1.
In order for the JP87 options to operate on this PCB, JP44 MUST be
removed.
MAXTOR XT-3000 OEM MANUAL 1011005 REV. C
Interface Termination
---------------------
As shipped, all assigned interface signal lines are terminated with a
removable 220/330 ohm resistor network. The first device and the last
device on the daisy-chain SCSI bus must be terminated. Remove the
terminators from any devices in between. For instance, if the XT-3000
is in the middle of the string, remove its terminators. Any host
adapters beeing used should be terminated in a similar fashion.
The devices driving the drive inpute should be open collector devices
capable of sinking at least 48 milliamps at a voltage level of less
than 0.5 VDC (7438 or equivalent).
Devices receiving the drive outputs should be of "SCHMITT" trigger
type to improve noise immunity, 74LS14, 74LS240 or equivalent. The
host adapter should not load the bus with more than one standard
LSTTL input load per line, and should terminate the drive output
signals with 220/330 ohm terminators.
MAXTOR XT-3000 OEM MANUAL 10111005 REV. C
Seek Time
---------
| XT3170 | XT3380 |
| XT3280 | |
----------------------------------+--------+--------+
Track-to-Track msec. typ. | 4 | 4 |
Average msec. typ. | 30 | 27 |
Average msec. max. | 54 | 52 |
----------------------------------+--------+--------+
Includes settling
Reliability Specifications
--------------------------
MTBF 20,000 POH, typical usage
PM Not required
MTTR 30 minutes
Component Design Life 5 years
Formatted Capacity
------------------
XT-3170/XT-3280
+------------+--------+-------+--------+
|Bytes/Sector| 256 | 512 | 1024 |
+------------+--------+-------+--------+
|Sector/track| 46 | 26 | 14 |
+------------+--------+-------+--------+
|MB | 129,72 | 146,64| 157,93|
+------------+--------+-------+--------+
XT-3380
+------------+--------+-------+--------+
|Bytes/Sector| 256 | 512 | 1024 |
+------------+--------+-------+--------+
|Sector/track| 59 | 34 | 18 |
+------------+--------+-------+--------+
|MB | 277,31 | 319,61| 338,41|
+------------+--------+-------+--------+
|
|
|
|
 |
|