Hard Drive: HITACHI: DK516C-16D 1288MB 5.25"/FH SCSI1 DIFF
D K 5 1 6 C - 1 6 D HITACHI
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 2172| | |
Capacity form/unform 1288/ 1600 MB Heads 15| | |
Seek time / track 13.5/ 3.0 ms Sector/track 81| | |
Controller SCSI1 DIFFERENTIAL Precompensation
Cache/Buffer 256 KB Landing Zone
Data transfer rate 3.000 MB/S int Bytes/Sector 512
5.000 MB/S ext SYNC
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 10 50 | -40 60
Power: sleep W Humidity % 8 80 | 8 90
standby W Altitude km 3.000| 12.000
idle W Shock g 2 | 20
seek W Rotation RPM 3600
read/write W Acoustic dBA 50
spin-up W ECC Bit
MTBF h 150000
Warranty Month
Lift/Lock/Park YES Certificates
Layout
HITACHI DK516C-16 CONSICE MANUAL REV 5/5.93 K2500416
+------------------------------------------------------------+ | +-J5--+ 1-2| | +-----+ J8| || | 7-8| | 1+--+2 +--+ | | | |XX I | | JP2 |XX N |+-+ 9+-JP3---+1 | | |XX T || J6 10+-------+2 | | |XX E |+-+ 15+--+16 |XX R J1 |+-+ JP4 JP5 3+--+1 |XX F || | +1+ 4+--+2 |XX A || | 1--2 +2+ TM180---+ |XX C || | | | Terminator | |XX E || J4 | |JP6 | |JP7-+ |+-+J7 || | | | |++ | +-+ |+-+ || | 9--10 +++-+ |XX J3 |+-+ |XX Power +---------------------------------------------------------+
Jumpers
HITACHI DK516C-16 CONSICE MANUAL REV 5/5.93 K2500416
Jumper Setting
==============
x = Jumpers at the shipment
The following jumpers are accessible for the user (use green jumper
plugs, as for J8 use blue jumper plugs):
SCSI ID setting jumper J8
SCSI bus parity jumper J8
Terminator power on/off jumper JP5
Write protected jumper JP4
Motor Auto-start option jumper JP2
Synchronized spindle jumper JP3
Synchronized spindle Terminator JP7
Synchronized spindle signal connector J7 Pins 1-2, 3-4
Note: The DK516C jumpers other than listed above are installed by the
manufacturer (black jumper plugs) and must not be modified or
replaced by the user.
J8 SCSI ID
------------
SCSI ID (0,1,2)
+-+-+
J8+8-6-4-2+
|: : : :|
+7-5-3-1+
+-- SCSI bus Parity
+----------+-----------------------+ | SCSI ID | 3-4 5-6 7-8 | | | ID2 | ID1 | ID0 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | | 1 | OPEN | OPEN | CLOSED| | 2 | OPEN | CLOSED| OPEN | | 3 | OPEN | CLOSED| CLOSED| | 4 | CLOSED| OPEN | OPEN | | 5 | CLOSED| OPEN | CLOSED| | 6 | CLOSED| CLOSED| OPEN | | x 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+
J8 1-2 SCSI bus parity
------------------------
x 1-2 OPEN Enables SCSI bus parity
CLOSED Disables SCSI bus parity
JP5 Terminator Power
---------------------
+4-3+ Pins 2-1
|o o| CLOSED +5V source for terminator is supplied from the SCSI
|o o| bus (host) (Pins 4-3 OPEN)
+2-1+ x OPEN +5V source for terminator is supplied only from the
drive controller. (Pins 4-3 CLOSED)
Note: Terminator power source is supplied to the terminator resistor
module from the host that pulls up the SCSI interface signals in the
controller so that the SCSI bus lines will not be pulled down when
DK516C power is turned down.
JP4 Write Protected
--------------------
CLOSED Write protected. The disk can be only read and cannot be
written.
x OPEN Read or write. The disk is enabled for both read and
write.
JP2 15-16 Motor Auto-start option
----------------------------------
x 15-16 CLOSED The spindle motor is started automatically when power
is turned on.
OPEN The Spindle motor is not started automatically when
power is turned on. It can be started by using SCSI
command to start the drive.
J7 Spindle Synchronization
----------------------------
J7 3+-+-+1
+-+-+ The cable array shall be configured as below
----4+-+-+2--
+--------------o--------------+ | +--------+-+ +--------+-+ | | | | | | | | | | | | ++-+-+-+-----+ ++-+-+-+-----+ ++-+-+-+-----+ | +---+--+ | | +---+--+ | | +---o--+ | |1 2 3 4 | | |1 2 3 4 | | |1 2 3 4 | | |G S N S +JP7| | +JP7| | +JP7| x = OPEN |E Y C Y |X| | | |x| | | |X| | |N N N +-+ | | +-+ | | +-+ | X = CLOSED | C C | | | | | |+-+++-+ | |+-+++-+ | |+-+++-+ | | J7 | | J7 | | J7 | | DK516C | | DK516C | | DK516C | +------------+ +------------+ +------------+
JP7 Terminator (Spindle Synchronization)
-----------------------------------------
Terminator Jumper JP7 shall be removed from all drives except the
drives located at eiher cable end.
JP3 1 4 Synchronized spindle jumper
------------------------------------
+---+JP3
x 1-2 CLOSED |o o|
x 3-4 CLOSED Off Line (Not supported) |o o|
OPEN |o o|
OPEN Not specified |o o|
|o o|
1-2 OPEN +2-1+
3-4 CLOSED Slave
1-2 CLOSED
3-4 OPEN Master
The Synchronized spindle option can be supported by the combination
of these jumpers. The mode to be supported will be decided when power
is turned on. The mode can be confirmed by MODE SENSE command and
changed by MODE SELECT command*
Install
HITACHI DK516C-16 CONSICE MANUAL REV 5/5.93 K2500416
Notes on Installation
=====================
Possible Orientations
---------------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
Whenever you change the orientation of the drive it is recommended to
reformat the disks.
Mounting
--------
In order to prove the shock protection ability, design the cabinet of
a system as described in below.
- Fix the drive with four screws by using the proper 4 screw holes
(total of 8 holes) of the drive.
- The insertion depth of the mounting screws below the drive surfaces
must be less than
3.5mm (0.14inch) for side holes
5 mm (0.2 inch) for bottom holes
Sequential Activation of Motors
-------------------------------
When multiple disk drives are connected and turned on simultaneously,
a large amount of current will flow. It is recommended to turn the
motors on one by one at an interval of approx. 35 seconds. Indication
of "READY" on the last drive reports that all drives have been
activated.
J3 DC Power and pin connector assignments
-------------------------------------------
+--------------+
|+-----J3-----+| pin 1 +12 VDC
|| 1 2 3 4 || pin 2 +12 Volts Return (GND)
|+------------+| pin 3 + 5 Volts Return (GND)
+--------------+ pin 4 + 5 VDC
(shown on the drive side)
Connectors
----------
Connector on PCB BERG 65625-108 Male 8 x Square Pin
Jumper plugs inserting at J8 JAE PS-2SH4B-2BH For Square Pin
Cable Connector BERG 65043-XX Female (XX = 33 (8 Pin), 34 (6 Pin)
Terminator
----------
The terminator of the controller other than last drive of SCSI Daisy
Chain must be removed.
My Books
